Manuals / Ryobi Outdoor / Lawn and Garden / Trimmer

Ryobi Outdoor CS30, SS30, BC30 Call Us First, 4050, Troubleshooting, call the Ryobi Help Line

Models: CS30, SS30, BC30

1 28

Download 28 pages 21.03 Kb

Page 24

Image 24

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

	PROBLEM	POSSIBLE CAUSE		SOLUTION

Spool retainer hard to turn:		1.	Screw threads are dirty or	1.	Clean threads and lubricate with grease - if no
			damaged.		improvement, replace the spool retainer.

Grass wraps around		1.	Cutting tall grass at ground level.	1.	Cut tall grass from the top down to prevent
driveshaft housing and string					wrapping.
head:		2.	Operating trimmer at part	2.	Operate trimmer at full throttle.
			throttle.

	CALL	4050
		4050
		-
	860
	-
800
-
1

CALL US FIRST

For any questions about operating or maintaining your trimmer, or brushcutter

call the Ryobi® Help Line !

Your trimmer has been fully tested prior to shipment to ensure

your complete satisfaction.

Page 24

Image 24

Ryobi Outdoor CS30, SS30, BC30 Call Us First, 4050, Troubleshooting, call the Ryobi Help Line, your complete satisfaction

Contents

OPERATORS MANUAL 30cc String Trimmers and Brushcutters RY30000 SeriesSAVE THIS MANUAL FOR FUTURE REFERENCE CALL US FIRST 4050INTRODUCTION TABLE OF CONTENTSGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USESPECIFIC SAFETY RULES FOR BRUSHCUT- TER AND BLADE USE SYMBOLS SYMBOLNAME EXPLANATIONSAVE THESE INSTRUCTIONS SYMBOLSSERVICE SYMBOL SIGNALSPECIFICATIONS UNPACKINGWeight - without fuel String cutting widthFEATURES DRIVE SHAFT HOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS DEFLECTORSTARTER GRIP AND ROPE REAR HANDLE TRIGGER LOCK PRIMER BULB COUPLERFEATURES DRIVE SHAFT HOUSING FRONT HANDLECOUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSING STARTER GRIP AND ROPE REAR HANDLEASSEMBLY See FigureGUIDE STRING TRIMMER SHAFT COUPLERASSEMBLY See FigureSee Figure FRONT HANDLEASSEMBLY TO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30See Figure TO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30ASSEMBLY INSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEADGEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLY SLOT See FigureASSEMBLY INSTALLING THE TRI-ARC BLADE AND BRUSHCUTTER GUARDREMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD See FiguresOPERATION FUEL MIXTUREHIGH QUALITY 2-CYCLE ENGINE OIL FILLING TANKOPERATION TO ADVANCE THE CUTTING LINECURVED SHAFT TRIMMER TO ADVANCE THE CUTTING LINE MANUALLYOPERATION See FiguresBLADE THRUST TRI-ARC BLADEIGNITION SWITCH TRIGGER LOCK THROTTLE TRIGGER IGNITION SWITCH PRIMER BULB TRIGGER LOCK THROTTLE TRIGGEROPERATION See Figures 21MAINTENANCE To install the spool retainerNEW PREWOUND SPOOL See FiguresMAINTENANCE See Figures 26String Diameter To remove the spool retainerMAINTENANCE CLEANING THE EXHAUST PORT AND MUFFLERREPLACING AND CLEANING AIR FILTER SPARK ARRESTORMAINTENANCE FUEL CAPSPARK PLUG STORAGE 1 MONTH OR LONGERTROUBLESHOOTING PROBLEMSOLUTION POSSIBLE CAUSETROUBLESHOOTING PROBLEMSOLUTION CALL US FIRSTWARRANTY MANUFACTURERS WARRANTY COVERAGEOWNERS WARRANTY RESPONSIBILITIES MAINTENANCE REQUIREMENTSPage WARRANTY FUEL LINESFUEL CAP SPARK PLUGRYOBI TECHNOLOGIES INC SERVICEHOW TO ORDER REPAIR PARTS OPERATORS MANUAL