Manuals / Ryobi Outdoor / Lawn and Garden / Trimmer

Ryobi Outdoor CS30, SS30, BC30 manual Operation, See Figures 21, To Start A Cold Engine

Models: CS30, SS30, BC30

1 28

Download 28 pages 21.03 Kb

Page 18

Image 18

OPERATION

STARTING AND STOPPING

See Figures 21 - 23.

TO START A COLD ENGINE:

DO NOT squeeze the throttle trigger until the engine starts and runs.

nLay the trimmer on a flat, bare surface.

nPRIME - Press the primer bulb 7 times.

nSET the start lever to the START position.

nPULL the rope until the engine starts.

nAllow the engine to run for 15 seconds.

nSqueeze trigger lock and throttle trigger.

NOTE: Squeezing the throttle trigger releases the start lever to the RUN position.

TO START A WARM ENGINE: PULL the rope until the engine starts.

TO STOP THE ENGINE:

Press and hold the switch in the stop “ ” position until the engine stops.

IGNITION

SWITCH

TRIGGER

LOCK

THROTTLE

TRIGGER

Fig. 21

IGNITION

SWITCH

PRIMER BULB

TRIGGER

LOCK

THROTTLE TRIGGER

Fig. 22

START LEVER

START

POSITION

START LEVER

RUN

POSITION

Fig. 23

Page 18

Image 18

Ryobi Outdoor CS30, SS30, BC30 manual Operation, See Figures 21, To Start A Cold Engine, To Stop The Engine

Contents

OPERATORS MANUAL 30cc String Trimmers and Brushcutters RY30000 SeriesSAVE THIS MANUAL FOR FUTURE REFERENCE INTRODUCTION CALL US FIRST4050 TABLE OF CONTENTSGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USESPECIFIC SAFETY RULES FOR BRUSHCUT- TER AND BLADE USE NAME SYMBOLSSYMBOL EXPLANATIONSERVICE SAVE THESE INSTRUCTIONSSYMBOLS SYMBOL SIGNALWeight - without fuel SPECIFICATIONSUNPACKING String cutting widthSTARTER GRIP AND ROPE REAR HANDLE TRIGGER LOCK PRIMER BULB FEATURESDRIVE SHAFT HOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS DEFLECTOR COUPLERCOUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSING FEATURESDRIVE SHAFT HOUSING FRONT HANDLE STARTER GRIP AND ROPE REAR HANDLEGUIDE ASSEMBLYSee Figure STRING TRIMMER SHAFT COUPLERSee Figure ASSEMBLYSee Figure FRONT HANDLESee Figure ASSEMBLYTO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30 TO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLY SLOT ASSEMBLYINSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD See FigureREMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD ASSEMBLYINSTALLING THE TRI-ARC BLADE AND BRUSHCUTTER GUARD See FiguresHIGH QUALITY 2-CYCLE ENGINE OIL OPERATIONFUEL MIXTURE FILLING TANKCURVED SHAFT TRIMMER OPERATIONTO ADVANCE THE CUTTING LINE TO ADVANCE THE CUTTING LINE MANUALLYBLADE THRUST OPERATIONSee Figures TRI-ARC BLADEOPERATION IGNITION SWITCH TRIGGER LOCK THROTTLE TRIGGERIGNITION SWITCH PRIMER BULB TRIGGER LOCK THROTTLE TRIGGER See Figures 21NEW PREWOUND SPOOL MAINTENANCETo install the spool retainer See FiguresString Diameter MAINTENANCESee Figures 26 To remove the spool retainerREPLACING AND CLEANING AIR FILTER MAINTENANCECLEANING THE EXHAUST PORT AND MUFFLER SPARK ARRESTORSPARK PLUG MAINTENANCEFUEL CAP STORAGE 1 MONTH OR LONGERSOLUTION TROUBLESHOOTINGPROBLEM POSSIBLE CAUSESOLUTION TROUBLESHOOTINGPROBLEM CALL US FIRSTOWNERS WARRANTY RESPONSIBILITIES WARRANTYMANUFACTURERS WARRANTY COVERAGE MAINTENANCE REQUIREMENTSPage FUEL CAP WARRANTYFUEL LINES SPARK PLUGHOW TO ORDER REPAIR PARTS RYOBI TECHNOLOGIES INCSERVICE OPERATORS MANUAL