Manuals / Ryobi Outdoor / Lawn and Garden / Trimmer

Ryobi Outdoor CS30, SS30, BC30 manual Maintenance, See Figures 26, String Diameter, Second String

Models: CS30, SS30, BC30

1 28

Download 28 pages 21.03 Kb

Page 20

See Figures 26 - 28.

MAINTENANCE

STRING REPLACEMENT

See Figures 26 - 28.

Use only monofilament string. Use original manufacturer's replacement string for best performance.

String Diameter:

CS30 - .080 in. (2.0 mm)

SS30 - .095 in. (2.4 mm)

BC30 - .095 in. (2.4 mm)

1.Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for models CS30.

Turn the spool retainer clockwise for models SS30 and BC30.

2.Remove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool.

3.Cut two pieces of string, each being approximately 9 ft. (2.7 m) long.

4.Insert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool.

5.Repeat above step with second string, using the bottom part of spool. Do not overfill.

6.Replace the spool and the spool retainer. Refer to “Spool Replacement” earlier in this manual.

SPRING

FIRST STRING

FIRST STRING

SLOT

SLOT

SPOOL

ARROWS ON

SPOOL

ANCHOR HOLE

Fig. 26

SECOND

STRING

Fig. 27

ARROWS ON

SPOOL

Fig. 28

Page 20

Image 20

Ryobi Outdoor CS30, SS30, BC30 Maintenance, See Figures 26, String Diameter, To remove the spool retainer, Second String

Contents

SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATORS MANUAL30cc String Trimmers and Brushcutters RY30000 Series CALL US FIRST 4050INTRODUCTION TABLE OF CONTENTSGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES FOR BRUSHCUT- TER AND BLADE USE SPECIFIC SAFETY RULESSPECIFIC SAFETY RULES FOR TRIMMER USE SYMBOLS SYMBOLNAME EXPLANATIONSAVE THESE INSTRUCTIONS SYMBOLSSERVICE SYMBOL SIGNALSPECIFICATIONS UNPACKINGWeight - without fuel String cutting widthFEATURES DRIVE SHAFT HOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS DEFLECTORSTARTER GRIP AND ROPE REAR HANDLE TRIGGER LOCK PRIMER BULB COUPLERFEATURES DRIVE SHAFT HOUSING FRONT HANDLECOUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSING STARTER GRIP AND ROPE REAR HANDLEASSEMBLY See FigureGUIDE STRING TRIMMER SHAFT COUPLERASSEMBLY See FigureSee Figure FRONT HANDLEASSEMBLY TO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30See Figure TO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30ASSEMBLY INSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEADGEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLY SLOT See FigureASSEMBLY INSTALLING THE TRI-ARC BLADE AND BRUSHCUTTER GUARDREMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD See FiguresOPERATION FUEL MIXTUREHIGH QUALITY 2-CYCLE ENGINE OIL FILLING TANKOPERATION TO ADVANCE THE CUTTING LINECURVED SHAFT TRIMMER TO ADVANCE THE CUTTING LINE MANUALLYOPERATION See FiguresBLADE THRUST TRI-ARC BLADEIGNITION SWITCH TRIGGER LOCK THROTTLE TRIGGER IGNITION SWITCH PRIMER BULB TRIGGER LOCK THROTTLE TRIGGEROPERATION See Figures 21MAINTENANCE To install the spool retainerNEW PREWOUND SPOOL See FiguresMAINTENANCE See Figures 26String Diameter To remove the spool retainerMAINTENANCE CLEANING THE EXHAUST PORT AND MUFFLERREPLACING AND CLEANING AIR FILTER SPARK ARRESTORMAINTENANCE FUEL CAPSPARK PLUG STORAGE 1 MONTH OR LONGERTROUBLESHOOTING PROBLEMSOLUTION POSSIBLE CAUSETROUBLESHOOTING PROBLEMSOLUTION CALL US FIRSTWARRANTY MANUFACTURERS WARRANTY COVERAGEOWNERS WARRANTY RESPONSIBILITIES MAINTENANCE REQUIREMENTSPage WARRANTY FUEL LINESFUEL CAP SPARK PLUGRYOBI TECHNOLOGIES INC SERVICEHOW TO ORDER REPAIR PARTS OPERATORS MANUAL