Operation, See Figures 21, 22, and | Ryobi Outdoor SS30 ZR30002

See Figures 21, 22, and 23.

OPERATION

STARTING AND STOPPING

See Figures 21, 22, and 23.

Trimmer should be on a flat, bare surface for starting.

1.Slowly press the primer bulb seven (7) times.

2.Set the choke lever to the FULL CHOKE position (A).

3.Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than eight (8) times.

NOTE: Keep throttle trigger squeezed fully through STEP 6.

4.Set the choke lever to the HALF CHOKE position (B).

5.Pull the starter handle until the engine runs. Do not pull the starter handle more than six (6) times.

6.Allow the engine to run for 15 seconds, then set the choke lever to the RUN position (C).

TO STOP THE ENGINE:

See Figure 21.

To stop the engine, depress the switch to the stop position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have.

For Help Call: 1-800-860-4050

IGNITION SWITCH

THROTTLE

TRIGGER

Fig. 21

PRIMER BULB

STARTER GRIP

IGNITION

SWITCH

STARTING

INSTRUCTION

LABEL

THROTTLE TRIGGER

Fig. 22

CHOKE LEVER

RUN (C)

HALF

CHOKE (B)

FULL

CHOKE (A)

Fig. 23

Page 18

Image 18

Ryobi Outdoor SS30 ZR30002, CS30 ZR30000 manual Operation, See Figures 21, 22, and, To Stop The Engine, For Help Call

Contents

ZR30000 Series OPERATORS MANUAL30cc String Trimmers and Brushcutter SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS INTRODUCTION GENERAL SAFETY RULES READ ALL INSTRUCTIONS SPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USE NAME SYMBOLSSYMBOL EXPLANATION SYMBOL SIGNAL SAVE THESE INSTRUCTIONSSERVICE MEANING Weight - without fuel SPECIFICATIONSUNPACKING String cutting width REAR HANDLE FEATURESHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS CHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFT COUPLER COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGSTARTER GRIP THROTTLE TRIGGER STRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTON ASSEMBLYSee Figure POSITIONING HOLE KNOB BOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 in FRONT HANDLE LOCK WASHER WING NUT BOLTFLAT WASHER HANDLE STRAP HANGER CLAMP BOLT BRACKET TO ATTACH THE CURVED SHAFT GRASS DEFLECTORZR30000 See Figure SLOT GEAR HEAD REMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYLATCH STRAP HANGER SHOULDER See Figures 10 and INSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD SLOT LOOSEN TIGHTENGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER FUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL OPERATIONFUEL MIXTURE GASOLINE CUTTING TIPS TO ADVANCE THE CUTTING LINETO ADVANCE THE CUTTING LINE MANUALLY See Figures 16 and TRI-ARCBLADE See Figures 19 andBLADE THRUST CUTTING TECHNIQUE - BLADE See Figures 21, 22, and IGNITION SWITCH THROTTLE TRIGGERPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING TO STOP THE ENGINE NEW PREWOUND SPOOL MAINTENANCETo install the spool retainer See Figures 24 and FIRST STRING See Figures 26, 27, andARROWS ON SPOOL ANCHOR HOLE FIRST STRING SLOT SECOND STRING LATCH PULL COVER TO OPEN Cleaning InstructionsSee Figures 29 and FILTER SLOTS ON AIR FILTER BASE TABS ON AIR FUEL CAP SPARK PLUGSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW OWNERSWARRANTY RESPONSIBILITIES WARRANTYMANUFACTURERS WARRANTY COVERAGE MAINTENANCE REQUIREMENTS 5 Hours Emissions PartsEach Use AIR FILTER ASSY NOTES • HOW TO ORDER REPAIR PARTS RYOBI TECHNOLOGIES INC• SERVICE • MODEL NO. AND SERIAL NO