Manuals / Samson / Home Audio / Stereo System

Samson UH-5 UT-5 Multi-PinWiring Chart, Manufacturer Model No.Pin 1Pin, Pin Information, +9 VDC

Models: DA-5L UH-5 UR-5 UR-5D UT-5

1 40

Download 40 pages 17.51 Kb

Page 28

UT-5 Multi-Pin Wiring Chart

Manufacturer Model No.Pin 1Pin 2

———————————————————————————————————

AKG	C409 Horn Mic	Shield		White/Clear
AKG	C410 Headset	Shield		White/Clear
Audio Technica	AT-831	Red (2x)		Yellow (2x)
Audio Technica	ATM-71	Red (2x)		Yellow (2x)
Audio Technica	ATM-75 Headset	Red (2x)		Yellow (2x)
Audio Technica	PRO8 Headset	N/C		Red (2x)
Audio Technica	MT-350	15KΩ	Resistor	White/Clear
		to pin 2
Countryman	Isomax Headset	Red		Green
PSC	PSC/P6	Red		White
Samson	ECM-40	15KΩ	Resistor	White/Clear
		to pin 2
Sanken	COS-11PT	Black		White/Clear
Sennheiser	MKE-2	Red		Blue
Sennheiser	MKE-2R	Red		8.2 KΩ Resistor
	(Red Dot)			to pin 1
Sennheiser	MKE-40	Red		Blue
Shure	SM10A	N/C		Red
Sony	ECM-44	Red		White/Clear
Sony	ECM-55	Red		White/Clear
Sony	ECM-77	Red		White/Clear
Sony	ECM-144	15KΩ	Resistor	White/Clear
		to pin 2
High Impedance	GC-1/P6	N/C		N/C
Guitar
Low Impedance	MC-1/P6	N/C		N/C
Guitar
Keyboards	GC-1/P6	N/C		N/C
Pin Information		+9 VDC		Audio

26

Image 28

Samson UH-5, UR-5D, DA-5L manual UT-5 Multi-PinWiring Chart, Manufacturer Model No.Pin 1Pin, Pin Information, +9 VDC, Audio

Contents

SAMSON S Y N T H E S I Z E DU H F T R U E D I V E R S I T Y W I R E L E S S S Y S T E MIntroduction System Features Guided Tours Introduction The concept behind a “true diversity” wireless system is that a single chassis houses two discrete receivers called “channel A” and “channel B” instead of one, with both tuned to the same frequency but with each using an independent antenna. A built-incomputer chip then continu- ously scans the two receivers and determines which one has the clear- est and strongest reception, automatically and silently switching to that channel. This allows you to maintain the wireless communication link over a much broader area range than would be allowed by a single receiver and also virtually eliminates interference and phase cancella- tion problems. In addition, our special circuitry, which utilizes the UHF Ultra High Frequency band, delivers the highest-qualitysound available in any wireless system. Finally, the provision of dbx noise reduction* produces crystal-clearsound with minimized background noise and hiss. Your UHF Synthesized True Diversity System may also optionally include a DA-5LUHF Antenna Distribution Amplifier. For more information on this device, see pages IntroductionSystem Features System Features Shure SM87 Condenser Shure SM85 CondenserGuided Tour - UR-5/UR-5DFront Panel Guided Tour - UR-5/UR-5DFront Panel Guided Tour - UR-5/UR-5DFront Panel 5b5d5e5cGuided Tour - UR-5/UR-5DRear Panel Guided Tour - UR-5/UR-5DRear Panel Guided Tour - UT-5 UT-5INPUT OFF ON1 Power on-offswitch* - Use this to turn the UT-5on or off to conserve battery power, be sure to leave it off when not in use Guided Tour - UT-56 Group selector - Use the supplied plastic screwdriver to set this to the desired Group this must match the Group setting of the receiver- see the “Setting Up and Using the UHF Synth System” section on page 16 for more information Guided Tour - UT-5Guided Tour - UH-5 WIRELESS MICROPHONESAMSON BATT1 Power on-offswitch* - Use this to turn the UH-5on or off to conserve battery power, be sure to leave it off when not in use Guided Tour - UH-57 Audio off-onswitch - When set to the “on” position, audio signal is transmitted. When set to the “off” position, the audio signal is muted. Because the carrier signal remains during muting, no “pop” or “thud” will be heard. Note that turning this off does not turn off the transmitter power-itis simply a way to temporarily mute the transmission of audio signal. If you don’t plan on using the transmitter for extended periods, turn off the transmitter power by using the power on-offswitch see #1 on the previous page. As described on page 20 of this manual, setting the UT-5Audio switch to the “on” position operates a tone squelch feature by causing a 38.4 kHz signal to be added to the carrier. The illuminated word “MUTE” in the UR-5and UR-5Ddisplay is a visual representation of the absence of this 38.4 kHz signal. When “MUTE” is lit, either the transmitter Audio switch is in the “off” position or the currently selected Group and Channel do not match that of the transmitter Guided Tour - UH-5Setting Up and Using the UHF Synth System Setting Up and Using the UHF Synth System tions are more prone to feedback problems than unidirectional cardioid or supercardioid ones in general, you can avoid feedback by taking care not to use any microphone directly in front of a PA speaker if this is unavoidable, you can try using an equalizer to attenuate those high frequencies which are causing the feedback “squealing”Setting Up and Using the UHF Synth System 7.Turn on the power to the UT-5or UH-5transmitter using its Power on-offswitch and observe the RF Level display in the UR-5or UR-5Dreceiver all segments should light up. When first setting up the UHF Synth System in a new environment, it’s always a good idea to do a walkaround while experimenting with different Group and Channel settings-youmay find that some cause more RF Level segments to light up than others the more segments light, the stronger the signal. Always pick the Group that has the greatest number of clear Channels and the Channel providing the strongest signal. Note that whenever a new channel is selected, it takes approximately five seconds for audio signal to be passed through to the receiver outputsSetting Up and Using the UHF Synth System segments should light up. If you are using the UT-5transmitter with a connected instrument, play the instrument at normal performance level while slowly raising the equivalent AF Level knob on the receiver to a level of approximately “8” again, one or more segments in the AF Level display should light up as you do soAbout dbx Noise Reduction About dbx Noise Reduction and Tone SquelchAbout Tone Squelch Trouble-shooting Problem No soundTrouble-shooting 8.Is the “Available” LED on the receiver lit and is the “Unavailable” LED on the transmitter off?Trouble-shooting Solution Try relocating the transmitter and/or receiver. In general, it’s best to minimize the distance between the two and also to try to keep a clear “line of sight,” so that the person wearing or using the transmitter can always see the receiver. If necessary, try relocating the receiver antennas to either the rear panel contact Samson Technologies for details about our rear panel mounting kit or remote them some distance from the receiver, using 50 ohm coaxial cable suitable for up to 1 gigaHertz bandwidth the lower the capacitance of the cable, the further you can remote the antennasUHF Synthesized Frequency Chart SAMSON UHF SYNTHESIZED FREQUENCY CHARTC H A N N E L G R O U PUT-5 Multi-pinLavalier Wiring Guide GC-1 MC-1UT-5 Multi-PinWiring Chart Manufacturer Model No.Pin 1PinPin Information +9 VDCUT-5 Multi-PinWiring Chart Pin 3Pin 4Pin 5PinGround Hi-ZAbout The DA-5LUHF Antenna Distribution Amplifier Guided Tour - DA-5LFront Panel Guided Tour - DA-5LRear Panel Setting Up and Using the DA-5L Third-partyantennas should not be substitutedSetting Up and Using the DA-5L 4.Connect the supplied 3-pin“EEC”DA-5LGrounding Techniques Glossary of Terms Glossary of Terms RF - Short for “Radio Frequency.”Transmitter RF SpecificationsTransmitter Audio Receiver SpecificationsDA-5L FCC Rules and Regulations