Manuals / Samson / Home Audio / Stereo System

Samson UH-5, UT-5, UR-5D, DA-5L manual Specifications, Transmitter RF, Transmitter Audio

Models: DA-5L UH-5 UR-5 UR-5D UT-5

1 40

Download 40 pages 17.51 Kb

Page 38

Specifications

Transmitter RF:

Type of Emission		110KF3E FM
RF Output Power		Max. 50 mW
Antenna Type		Built-in loop (UH-5)
		1/2 λ whip (UT-5)
Gain (Audio)		Less than 2.14 dB
Spurious Emissions	Less than -45 dB from carrier
Carrier Generation		Crystal controlled PLL
		synthesized oscillator
Stability		50 ppm
Tone Squelch Frequency		38.4 kHz
Battery Life (9-volt alkaline)		Approximately 7 hours
Weight (UH-5, without mic element)		111 g

Transmitter Audio:

Audio Frequency Response	40 Hz to 16 kHz
Frequency Deviation	20 kHz (@ -40 dBV)
Pre-emphasis	50 micro/sec.
Noise Reduction System	dbx type II
Audio Residual Noise	Less than -93 dBm
	(@ IHF - A Filter Weighted)
Audio Dynamic Range	More than 103 dB
	(@ IHF - A Filter Weighted)
Total Harmonic Distortion	Less than .5% (400 Hz,
	deviation @ 10 kHz)

36

Image 38

Samson UH-5, UT-5, UR-5D, DA-5L manual Specifications, Transmitter RF, Transmitter Audio

Contents

U H F T R U E D I V E R S I T Y W I R E L E S S SAMSONS Y N T H E S I Z E D S Y S T E MIntroduction System Features Guided Tours Introduction The concept behind a “true diversity” wireless system is that a single chassis houses two discrete receivers called “channel A” and “channel B” instead of one, with both tuned to the same frequency but with each using an independent antenna. A built-incomputer chip then continu- ously scans the two receivers and determines which one has the clear- est and strongest reception, automatically and silently switching to that channel. This allows you to maintain the wireless communication link over a much broader area range than would be allowed by a single receiver and also virtually eliminates interference and phase cancella- tion problems. In addition, our special circuitry, which utilizes the UHF Ultra High Frequency band, delivers the highest-qualitysound available in any wireless system. Finally, the provision of dbx noise reduction* produces crystal-clearsound with minimized background noise and hiss. Your UHF Synthesized True Diversity System may also optionally include a DA-5LUHF Antenna Distribution Amplifier. For more information on this device, see pages IntroductionSystem Features System Features Shure SM87 Condenser Shure SM85 CondenserGuided Tour - UR-5/UR-5DFront Panel Guided Tour - UR-5/UR-5DFront Panel Guided Tour - UR-5/UR-5DFront Panel 5b5d5e5cGuided Tour - UR-5/UR-5DRear Panel Guided Tour - UR-5/UR-5DRear Panel INPUT Guided Tour - UT-5UT-5 OFF ON1 Power on-offswitch* - Use this to turn the UT-5on or off to conserve battery power, be sure to leave it off when not in use Guided Tour - UT-56 Group selector - Use the supplied plastic screwdriver to set this to the desired Group this must match the Group setting of the receiver- see the “Setting Up and Using the UHF Synth System” section on page 16 for more information Guided Tour - UT-5SAMSON Guided Tour - UH-5WIRELESS MICROPHONE BATT1 Power on-offswitch* - Use this to turn the UH-5on or off to conserve battery power, be sure to leave it off when not in use Guided Tour - UH-57 Audio off-onswitch - When set to the “on” position, audio signal is transmitted. When set to the “off” position, the audio signal is muted. Because the carrier signal remains during muting, no “pop” or “thud” will be heard. Note that turning this off does not turn off the transmitter power-itis simply a way to temporarily mute the transmission of audio signal. If you don’t plan on using the transmitter for extended periods, turn off the transmitter power by using the power on-offswitch see #1 on the previous page. As described on page 20 of this manual, setting the UT-5Audio switch to the “on” position operates a tone squelch feature by causing a 38.4 kHz signal to be added to the carrier. The illuminated word “MUTE” in the UR-5and UR-5Ddisplay is a visual representation of the absence of this 38.4 kHz signal. When “MUTE” is lit, either the transmitter Audio switch is in the “off” position or the currently selected Group and Channel do not match that of the transmitter Guided Tour - UH-5Setting Up and Using the UHF Synth System Setting Up and Using the UHF Synth System tions are more prone to feedback problems than unidirectional cardioid or supercardioid ones in general, you can avoid feedback by taking care not to use any microphone directly in front of a PA speaker if this is unavoidable, you can try using an equalizer to attenuate those high frequencies which are causing the feedback “squealing”Setting Up and Using the UHF Synth System 7.Turn on the power to the UT-5or UH-5transmitter using its Power on-offswitch and observe the RF Level display in the UR-5or UR-5Dreceiver all segments should light up. When first setting up the UHF Synth System in a new environment, it’s always a good idea to do a walkaround while experimenting with different Group and Channel settings-youmay find that some cause more RF Level segments to light up than others the more segments light, the stronger the signal. Always pick the Group that has the greatest number of clear Channels and the Channel providing the strongest signal. Note that whenever a new channel is selected, it takes approximately five seconds for audio signal to be passed through to the receiver outputsSetting Up and Using the UHF Synth System segments should light up. If you are using the UT-5transmitter with a connected instrument, play the instrument at normal performance level while slowly raising the equivalent AF Level knob on the receiver to a level of approximately “8” again, one or more segments in the AF Level display should light up as you do soAbout Tone Squelch About dbx Noise Reduction and Tone SquelchAbout dbx Noise Reduction Trouble-shooting Problem No soundTrouble-shooting 8.Is the “Available” LED on the receiver lit and is the “Unavailable” LED on the transmitter off?Trouble-shooting Solution Try relocating the transmitter and/or receiver. In general, it’s best to minimize the distance between the two and also to try to keep a clear “line of sight,” so that the person wearing or using the transmitter can always see the receiver. If necessary, try relocating the receiver antennas to either the rear panel contact Samson Technologies for details about our rear panel mounting kit or remote them some distance from the receiver, using 50 ohm coaxial cable suitable for up to 1 gigaHertz bandwidth the lower the capacitance of the cable, the further you can remote the antennasC H A N N E L UHF Synthesized Frequency ChartSAMSON UHF SYNTHESIZED FREQUENCY CHART G R O U PUT-5 Multi-pinLavalier Wiring Guide GC-1 MC-1Pin Information UT-5 Multi-PinWiring ChartManufacturer Model No.Pin 1Pin +9 VDCGround UT-5 Multi-PinWiring ChartPin 3Pin 4Pin 5Pin Hi-ZAbout The DA-5LUHF Antenna Distribution Amplifier Guided Tour - DA-5LFront Panel Guided Tour - DA-5LRear Panel Setting Up and Using the DA-5L Third-partyantennas should not be substitutedSetting Up and Using the DA-5L 4.Connect the supplied 3-pin“EEC”DA-5LGrounding Techniques Glossary of Terms Glossary of Terms RF - Short for “Radio Frequency.”Transmitter Audio SpecificationsTransmitter RF DA-5L SpecificationsReceiver FCC Rules and Regulations