Connecting a Camcorder | Samsung CL21M6, CL21T21, CL21M21 specification

I N S TA L L AT I O N

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a Camcorder to your TV. They allow you to view the Camcorder tapes without using a VCR.

1

Locate the A/V output jacks on the Camcorder. They are usually found on the side or rear of the Camcorder.

2

Connect a set of audio cables between the “AV IN 2 (L, R)” jacks on the TV and the AUDIO OUT jacks on the Camcorder.

If you have mono Camcorder, connect L(mono) to Camcorder audio out using only one audio cable.

3

Connect a video cable between the “AV IN 2 (VIDEO)” jack on the TV and the VIDEO OUT jacks on the Camcorder.

The audio-video cables shown here are usually included with a

Camcorder. (If not, check your local electronics store.) If your

Camcorder is stereo, you need to connect a set of two cables.

Connecting to an Analog Amplifier

The “AV OUT (L, R)” jacks cannot be used for external speakers. You must hook them up to an amplifier.

When an audio amplifier is connected to the “AV OUT (L, R)” jacks: Decrease the gain (volume) of the audio amplifier, and adjust the volume level with the volume control on the TV.

English - 17

Image 17

Samsung CL21M6, CL21T21, CL21M21 manual Connecting a Camcorder, Connecting to an Analog Amplifier

Contents

Owner’s Instructions English Using the PRE-CH Button to Select the Previous Channel InstallationResetting the Picture Settings to the Factory Defaults Your New TV Appendix Special FeaturesTroubleshooting Accessories List of Features ¨ Remote Control Sensor IndicatorFamiliarizing Yourself with the TV Control Buttons Audio Input Connection Jacks Side´ Video Input Headphone Audio-Video Output jacks ¨ S-Video Input jack Connection Jacks Rear´ Video Input jacks Audio Input jacks ´ Number buttons Remote Control+100 VOL +, VOL Installing Batteries in the Remote Control Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF Antennas Separate VHF and UHF Antennas Antennas with 75-ohm Round Leads Cable without a Cable Box Connecting Cable TVConnecting to a Cable Box that Descrambles All Channels This terminal might be labelled ANT IN, VHF in or simply, Connecting to a Cable Box that Descrambles Some Channels Also, you can connect to AV in 2 on the side panel of TV Connecting a VCRConnecting a Second VCR to Record from the TV Connecting to Regular Audio and Video Jacks Connecting a DVD PlayerConnecting to Y, PB, PR Connecting to an Analog Amplifier Connecting a Camcorder You can also use the Power button on the front panel Plug & Play FeaturePlug & Play feature doesn’t work in the AV mode Turning the TV On and Off Refer to Setting the Clock on Viewing the Menus and On-Screen Displays Press the Info button on the remote controlViewing the Menus Viewing the Display Selecting a Menu Language Memorizing the Channels Selecting the Video Signal Source Storing Channels in Memory Automatic Method Adding and Erasing Channels Using the Number Buttons Using the Channel ButtonsUsing the PRE-CH Button to Select the Previous Channel Changing Channels Labelling the Channels You cannot select Name in the AV mode Press the Enter button again Using Automatic Picture SettingsPicture Control Customizing the Picture Resetting the Picture Settings to the Factory Defaults Sound Control Adjusting the VolumeUsing the Mute Button Using Automatic Sound Settings Select the balance or a Customizing the SoundSelect Equalizer, then Press the Enter button Setting the Clock Setting the Signal Source Viewing an External Signal Source Press the Enter button Press the Exit button to exit Assigning Names to External Input Mode Chapter Four Fine Tuning Channels Changing the Screen Size Digital Noise Reduction DNIe JrTM Digital Natural Image engine Press the Enter button to select PIP Viewing Picture-In-Picture depending on the modelActivating the PIP Changing the Size of the Sub Picture Selecting an External SourceSwapping the Sub Picture and Main Picture Changing the Channel of the Sub Picture You can select the Prog. when the Source is set to TVChanging the Position of the Sub Picture Using the R.Surf Feature Choosing a Multi-Channel Sound MTS track Auto Volume You must set the clock first Setting the On/Off TimerSet the Off Timer as methods for On Timer setting Setting the Preferred Channel and Volume Level Setting the Sleep Timer Press the Enter button to select Caption Viewing Closed Captions On-Screen Text Message Caption Mode Channel Field Move Enter Return Press the œ or √ button to select the channel to be locked Locking the ChannelIf you want to unlock a channel, set to Off Setting the Blue Screen Mode Setting the On/Off Melody Viewing the Demonstration Chapter Five Identifying Problems Specifications Cleaning and Maintaining Your TVUsing Your TV in Another Country M O English English AA68-03671A-00