Samsung DVD-HD747/FES manual Controlling a TV with the Remote, Firmware upgrade, Introduction

Controlling a TV with the Remote

The remote can also be set up to control most TVs. To program the remote, use the code that corresponds to your brand.

TV Codes

BRAND	CODE	BRAND	CODE
ANAM	10, 11, 12, 13, 14, 15, 16, 17, 18	NORDMENDE	72, 73
AIWA	82	NOKIA	74
BANG&OLUFSEN	57	PANASONIC	53, 54, 74, 75
BLAUPUNKT	71	PHILPS	06, 55, 56, 57
BRANDT	73	PHONOLA	06, 56, 57
BRIONVEGA	57	PIONEER	58, 59, 73, 74, 75
CGE	52	RADIOLA	06, 56
CONTINENTAL EDISON	75	RADIOMARELLI	57
DAEWOO	19, 20, 23, 24, 25, 26, 27, 28, 29,	RCA	45, 46
	30 , 31, 32, 33, 34	REX	74
EMERSON	64	SABA	57, 72, 73, 74, 75
FERGUSON	73	SALORA	74
FINLUX	06, 49, 57	SAMSUNG	01, 02, 03, 04, 05, 06, 07, 08, 09
FORMENTI	57	SANYO	41, 42, 43, 44, 48
FUJITSU	84	SCHNEIDER	06
GRADIENTE	70	SELECO	74
GRUNDIG	49, 52, 71	SHARP	36, 37, 38, 39, 48
HITACHI	60, 72, 73, 75	SIEMENS	71
IMPERIAL	52	SINGER	57
JVC	61, 79	SINUDYNE	57
LG	06, 19, 20, 21, 22, 78	SONY	35, 48
LOEWE	06, 69	TELEAVA	73
LOEWE OPTA	06, 57	TELEFUNKEN	67, 73, 75, 76
MAGNAVOX	40	THOMSON	72, 73, 75
METZ	57	THOMSON ASIA	80, 81
MITSUBISHI	06, 48, 62, 65	TOSHIBA	47, 48, 49, 50, 51, 52
MIVAR	52, 77	WEGA	57
NEC	83	YOKO	06
NEWSAN	68	ZENITH	63
NOBLEX	66
1. Turn on the TV.		4. If the TV turns off, setup is complete.
		Enter other codes of the same brand if the first
2. Point the DVD’s remote at the TV.		code does not work.
3. While holding the TV POWER button down, enter		5. To operate the TV, use the “TV Function Buttons”
the code for your brand.		described on page 8.

e.g) For Samsung 2 TVs	Important Note
	• The remote may not be able to control every
While holding down the TV POWER button,	model TV of the brands listed.
enter 0 and then 1.	• If you replace the remote control's batteries, set
	the brand code again.

Firmware upgrade

Introduction

Samsung will often support the software upgrade to improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung.com).

Because the specially new mpeg4 codec continues and it is appearing. What improvements are made depends on the upgrade software you are using as well as the software that your DVD-player contained before the upgrade.

How to make an upgrade disc

Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings:

1.You have to download a new file through Download Center of Samsung Internet Site (www.samsung.com).

2.Write the file to Disc using CD-RW of your computer.

Note

•File System CD-ROM ISO Level

•Character set ISO 9660

•Finalized, single session

•Write speed low

Upgrade procedure

1.Press OPEN/CLOSE to open the disc tray.

2.Insert the upgrade CD-R disc, label facing up.

3.Press OPEN/CLOSE to close the disc tray.

Firmware upgrade appears on the display

4.Press the ENTER button.

Firmware upgrade starts

5.In the middle of the writing, the tray will open automatically. After taking out the disc, please wait for about 2 minutes.

6.If the unit was successfully updated, the unit will turn off and on after closing the tray automatically. When the unit turns on, this screen will display.

7. Select the desired language.

Note • If the “Select Menu Language” does't appears, please contact to “Samsung Service Center”.

•Do not press any button and unplug the power code during upgrade.

•The upgrade procedure may change, refer to the web site (www.samsung.com).

ENG-38 ENG-39