Samsung DVD-ROM drive Connecting the Cables, Setting Up the Device Driver, Automatic Setup

Models: DVD-ROM drive

1 5
Download 5 pages 18.09 Kb
Page 3
Image 3
Connecting the Cables

Connecting the Cables

1 Connecting the power cable2 Installing a jumper on the master/slave select terminalSetting Up the Device Driver 1. Power cable

◆Automatic Setup◆Manual SetupAdd the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.4 Connecting the audio cable from a sound cardAdd the C:\SAMSUNG\MSCDEX /D:SSCD000 entry. 2. Master/slave select terminal

3. IDE cable

4. Audio cable

1 Connecting the power cable

The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the DVD-ROM drive.

2 Installing a jumper on the master/slave select terminal

Install the jumper in the correct position on the terminal:

MA to use the device in the master mode

SL to use the device in the slave mode

CS to control the device via a CSEL host interface signal

See Step 3 for further details.

3 Connecting the IDE cable

Two configurations are possible.

The DVD-ROM drive is the only IDE device in addition to the hard disk.

Setting Up the Device Driver

Automatic Setup

1Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive.

To do so, type A: after the C:\ prompt and press [Enter].

2Type CDSETUP and press [Enter].

3Reboot the computer.

Manual Setup

1 Make the C:\SAMSUNG directory.

2 Copy the files from the diskette to the C:\SAMSUNG directory.

To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press [Enter].

3 Edit the CONFIG.SYS file.

IDE port

Mother board

DVD-ROM

Hard disk

(SL)

(MA)

Install the jumper in the SL position (Slave). Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to the DVD-ROM drive and then to the hard disk.

Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.

LAST DRIVE = Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V

You already have an additional IDE device installed in your computer.

Second IDE cable

First IDE cable

 

 

 

Install the jumper in the MA position (Master).

 

 

 

Connect the 40-pin flat IDE cable from a second

 

 

Mother

IDE port on the mother board directly to

 

 

the DVD-ROM drive or first to another additional

 

 

board

 

 

IDE drive and then to the DVD-ROM drive.

DVD-ROM CD-ROM

 

Hard disk

Hard disk

(MA)

(SL)

(SL)

(MA)

4 Connecting the audio cable from a sound card

Connect the 4-pin audio cable between the sound output terminal on the DVD- ROM drive and the audio input terminal on the sound card.

4

4 Edit the AUTOEXEC.BAT file.

Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

C :\SAMSUNG\MSCDEX /D:SSCD000

5 Reboot the computer.

5

Page 3
Image 3
Samsung DVD-ROM drive warranty Connecting the Cables, Setting Up the Device Driver, Automatic Setup, Manual Setup