This terminal might be labeled | Samsung ST42W5P instruction

I N S T A L L AT I O N

Cable with a Cable box that Descrambles All Channels

1

Find the cable that is connected to the ANTENNA OUT terminal on your cable box. This terminal might be labeled “ANT OUT”, “VHF OUT”, or simply, “OUT”.

2

Connect the other end of this cable to the ANT-A or ANT-B terminal on the rear of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

1

Find and disconnect the cable that is connected to the ANTENNA IN ter- minal on your cable box.

2

Connect this cable to a two-way splitter.

▼	This terminal might be labeled

“ANT IN,” “VHF IN,” or simply, “IN.”

3

Connect a coaxial cable between an OUTPUT ter- minal on the splitter and the IN terminal on the cable box.

2.3 CHAPTER TWO: INSTALLATION

Image 16

Samsung ST42W5P manual Cable with a Cable box that Descrambles All Channels, This terminal might be labeled

Contents

Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Your New TV InstallationOperation Special Features Troubleshooting List of Features Chapter One Familiarizing Yourself with The TV Press to adjust for the optimum picture set in the Factory Side Panel Jacks´ Video Input jack Audio Input jacks Rear Panel Jacks Antenna terminals ¨ Audio Input jacksVideo Input jack Component 1480i, 480p Remote Control Power´ +100 StillMain ± Mode ˘ R.surf¿ S.Mode ¸ P.Mode Connecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin Leads Connecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable Box Connecting to a Cable Box that Descrambles Some Channels Cable with a Cable box that Descrambles All ChannelsThis terminal might be labeled ANT IN, VHF IN, or simply, Install AT I O N Connecting a VCR Connecting a Camcorder Connecting a Second VCR to Record from the TV Connecting a DVD Player, DTV Set-Top Box 480i, 480p Connecting to Y, PB, PR Connecting a DTV Set-Top Box 480p Install two AAA size batteries Replace the cover Installing Batteries in the Remote ControlMake sure to match the + Plug & Play Feature You can also use the Power button on the front panelPress the Power button Turning the TV On and Off 1Press the Menu button CH or CH button. refer to Setting the clock onRefer to Auto program on You can also select Perfect Using the Perfect Focus FeatureFocus by pressing the Perfect Focus button Adjusting Manual Convergence Adjust Red Convergence If a horizontal red line is visible, use Viewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting the Antenna Input Selecting a Menu LanguagePress the VOL + or VOL button to select a or B Memorizing the Channels Selecting the Video Signal-sourceANT antenna, STD, HRC or IRC TV automatically cycles Storing Channels in Memory Automatic MethodAdding and Erasing Channels Manual Method Using the Channel Buttons Using the Number ButtonsUsing the Previous Channel Changing Channels Selecting Your Favorite Channels To Store Your Favorite ChannelsCan be set as Favorite channels To View Your Favorite Channels Adding and Erasing Channels Manual Method Labeling in the A/V mode Labeling the ChannelsPress CH or CH to tune to the channel that will be labeled Select Channel, then After adjusting an item, Picture ControlCustomizing the Picture Gauge will automatically disappearafter about 4 seconds Using Automatic Picture Settings Press the Menu button. Picture icon will be high- lighted Adjusting the Volume Using MuteSound Control Selecting the Color Tone Customizing the Sound Press the Menu button exit Using Automatic Sound Settings Setting the Clock When selecting the hours, beSure to select the proper time of day AM or PM You press the Display button Viewing an External Signal Source Fine Tuning Channels After you adjust the fine tuningPress the VOL + or VOL button to adjust the fine tuning Star icon*will appear Digital Noise Reduction Press the CH button to select Digital NR Cinema Changing the Screen SizePress the Aspect button to change the screen Using the R.surf feature Setting the On/Off Timer Before using the timer, you must Setting the Sleep Timer To deactivate the On timeSelect Off during this step If no function buttons Extra sound settings Surround, Auto Volume, Melody, BBE Surround Quick way to access the MTS Choosing a Multi-Channel Sound MTS Soundtrack Viewing Closed Captions Different channels and fieldsSelect Mode, then press Select Caption or Text Quick way to access the PIP Menu Simply press the PIP button on the remote controlViewing Picture-in-Picture Activating Picture-in-Picture Selecting a Signal Source Antenna or Cable for PIP Selecting a Signal Source External A/V for PIPQuick way to access the signal Select PIP, then press Swapping the Contents of the PIP Image and Main Image Changing the Size of the PIP Window Simply press the PIP CH button on the remote control Changing the Location Rotating in PIP modeChanging the PIP Channel Scanning the Available Channels Viewing the Demonstration Picture icon will beHighlighted blinking Select Demonstration Customizing Your Remote Control Setting Up Your Remote Control to Operate Your VCR or DVDRemote control has four Make sure you enter 3 digits Setting Up Your Remote Control to Operate Your Cable Box VCR Codes Cable BoxCodes DVD Codes Identifying Problems Chapter Five Using Your TV in Another Country Cleaning and Maintaining Your TVSpecifications M O Appendix A.3