Storing Channels in Memory Automatic Method | Samsung ST42W5P

O P E R AT I O N

Storing Channels in Memory (Automatic Method)

1

First, select the correct signal source (ANT, STD, HRC, IRC). See steps 1~2 on previous page.

Press the Menu button. Press the CH button to select “Channel”, then press the VOL + button


						Channel

				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

2

Press the CH button to select “Auto Program”, then press the VOL + button.


						Channel
				Antenna		: A
				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

3

The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reap- pears. Press the Menu button to exit.

▼	The TV automatically cycles

through all of the available chan- nels and stores them in memory. This takes about one to two min- utes.

Adding and Erasing Channels (Manual Method)

1

Use the number buttons to directly select the channel that will be added or erased.

2

Press the Add/Erase button:

Repeatedly pressing this button will alternate between “Added” and “Erased.”

Press the Menu button to exit.

You can view any channel (including an erased channel) by using the number buttons on the remote control.

CHAPTER THREE: TV OPERATION 3.9

Image 31

Samsung ST42W5P manual Storing Channels in Memory Automatic Method, TV automatically cycles

Contents

Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Your New TV InstallationOperation Troubleshooting Special Features Chapter One List of Features Familiarizing Yourself with The TV Audio Input jacks Press to adjust for the optimum picture set in the FactorySide Panel Jacks ´ Video Input jack Component 1480i, 480p Rear Panel JacksAntenna terminals ¨ Audio Input jacks Video Input jack StillMain Remote ControlPower ´ +100 ¸ P.Mode ± Mode˘ R.surf ¿ S.Mode Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF Antennas Cable without a Cable Box Connecting Cable TVAntennas with 75-ohm Round Leads Separate VHF and UHF Antennas ANT IN, VHF IN, or simply, Connecting to a Cable Box that Descrambles Some ChannelsCable with a Cable box that Descrambles All Channels This terminal might be labeled Install AT I O N Connecting a VCR Connecting a Second VCR to Record from the TV Connecting a Camcorder Connecting to Y, PB, PR Connecting a DVD Player, DTV Set-Top Box 480i, 480p Connecting a DTV Set-Top Box 480p Install two AAA size batteries Replace the cover Installing Batteries in the Remote ControlMake sure to match the + Turning the TV On and Off Plug & Play FeatureYou can also use the Power button on the front panel Press the Power button 1Press the Menu button CH or CH button. refer to Setting the clock onRefer to Auto program on You can also select Perfect Using the Perfect Focus FeatureFocus by pressing the Perfect Focus button Adjusting Manual Convergence If a horizontal red line is visible, use Adjust Red Convergence Viewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting the Antenna Input Selecting a Menu LanguagePress the VOL + or VOL button to select a or B Memorizing the Channels Selecting the Video Signal-sourceANT antenna, STD, HRC or IRC TV automatically cycles Storing Channels in Memory Automatic MethodAdding and Erasing Channels Manual Method Changing Channels Using the Channel ButtonsUsing the Number Buttons Using the Previous Channel To View Your Favorite Channels Selecting Your Favorite ChannelsTo Store Your Favorite Channels Can be set as Favorite channels Adding and Erasing Channels Manual Method Select Channel, then Labeling in the A/V modeLabeling the Channels Press CH or CH to tune to the channel that will be labeled Gauge will automatically disappearafter about 4 seconds After adjusting an item,Picture Control Customizing the Picture Press the Menu button. Picture icon will be high- lighted Using Automatic Picture Settings Selecting the Color Tone Adjusting the VolumeUsing Mute Sound Control Press the Menu button exit Customizing the Sound Using Automatic Sound Settings You press the Display button Setting the ClockWhen selecting the hours, be Sure to select the proper time of day AM or PM Viewing an External Signal Source Star icon*will appear Fine Tuning ChannelsAfter you adjust the fine tuning Press the VOL + or VOL button to adjust the fine tuning Press the CH button to select Digital NR Digital Noise Reduction Cinema Changing the Screen SizePress the Aspect button to change the screen Using the R.surf feature Before using the timer, you must Setting the On/Off Timer If no function buttons Setting the Sleep TimerTo deactivate the On time Select Off during this step Surround Extra sound settings Surround, Auto Volume, Melody, BBE Choosing a Multi-Channel Sound MTS Soundtrack Quick way to access the MTS Select Caption or Text Viewing Closed CaptionsDifferent channels and fields Select Mode, then press Activating Picture-in-Picture Quick way to access the PIPMenu Simply press the PIP button on the remote control Viewing Picture-in-Picture Select PIP, then press Selecting a Signal Source Antenna or Cable for PIPSelecting a Signal Source External A/V for PIP Quick way to access the signal Changing the Size of the PIP Window Swapping the Contents of the PIP Image and Main Image Scanning the Available Channels Simply press the PIP CH button on the remote controlChanging the Location Rotating in PIP mode Changing the PIP Channel Select Demonstration Viewing the DemonstrationPicture icon will be Highlighted blinking Make sure you enter 3 digits Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR or DVD Remote control has four Setting Up Your Remote Control to Operate Your Cable Box DVD Codes VCR CodesCable Box Codes Chapter Five Identifying Problems Using Your TV in Another Country Cleaning and Maintaining Your TVSpecifications M O Appendix A.3