Samsung UE55C7705WSXXE, UE55C7700WSXXN, UE55C7700WZXZG manual Manual Store, Satellite System Setup

When Antenna Source is set to Satellite:

■■ Channel Type (All / TV / Radio): Select the Channel type to memorise.

■■ Satellite: Selects the satellite to scan.

■■ Scan Mode (All Channels / Free Channels Only): Selects the scanning mode of the selected satellite.

Manual Store

(Not available when Antenna Source is set to Canal Digital Sat)

Scans for a channel manually and stores in the TV.

✎✎If a channel is locked using the Child Lock function, the PIN input window appears.

When Antenna Source is set to Air or Cable:

■■ Digital Channel: When scanning has finished, channels are updated in the channel list.

✎✎ When selecting Antenna → Air: Channel, Frequency, Bandwidth

✎✎ When selecting Antenna → Cable: Frequency, Modulation, Symbol Rate

■■ Analogue Channel (Programme, Colour System, Sound System, Channel, Search): If there is abnormal sound or no sound, reselect the sound standard required.

✎✎Channel mode

xx P (programme mode): When tuning is complete, the broadcasting stations in your area have been assigned to position numbers from P0 to P99. You can select a channel by entering the position number in this mode.

xx C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel.

When Antenna Source is set to Satellite:

■■ Satellite: Selects the satellite using the up/down buttons.

■■ Transponder: Selects the transponder using the up/ down buttons.

■■ Scan Mode (All Channels / Free Channels Only): Selects either free or all channels to store.

■■ Network Search (Disable / Enable): Enable / Disable network search using the up/down buttons.

■■ Signal Quality: Display the current status of broadcasting signal.

✎✎Information on a satellite and its transponder is subject to change depending on the broadcasting conditions.

✎✎When setting is completed, move to Search and press the ENTEREbutton. Channel scan is started.

Satellite System Setup	03FeaturesBasic
The PIN input screen appears. Enter your 4 digit PIN number.
Satellite System Setup is available when Antenna is set to
Satellite or Canal Digital Sat. Before running Auto Store,
Set Satellite System Setup. Then channel scan is run
normally.
■■ Satellite Selection: You can choose the satellites for
this TV.
✎✎ This function is available when Antenna is set to
Satellite.
■■ LNB Power (Off / On): Enables or disables the power
supply for the LNB.
■■ LNB Settings: Configures the outdoor equipment.

––Satellite: Selects the satellite for receiving digital broadcasts.

––Transponder: Selects a transponder from the list or adds a new transponder.

––DiSEqC Mode: Selects DiSEqC mode for the selected LNB.

––Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency.

––Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency.

––Tone 22 kHz (Off / On / Auto): Selects the Tone 22 kHz depending on the LNB type. For a universal LNB it should be Auto.

––Signal Quality: Display the current status of broadcasting signal.

■■ Positioner Settings: Configures the antenna positioner.

Positioner (On / Off): Enables or disables the positioned control.

Positioner Type (USALS / DiSEqC 1.2): Sets the positioned type between DiSEqC 1.2 and USALS(Universal Satellite Automatic Location System).

––My Longitude: Sets the longitude for my location.

––My Latitude: Sets the latitude for my location.

––Satellite Longitude Settings: Sets the longitude of user defined satellites.

User Mode: Sets the position of satellite antenna according to each satellite. If you store the current position of satellite antenna according to a certain satellite, when the signal of that satellite is needed, the satellite antenna can be moved to pre-populated position.

––Satellite: Selects the satellite to set the position for.

––Transponder: Selects a transponder from the list for signal reception.

––Moving Mode: Selects the movement mode between discrete and continuous movement.

––Step Size: Adjusts the step size degrees for the antenna rotation. Step Size is available when Moving Mode is set to Step.

English 15