useful tips for your drum washing machine

Cleaning the debris filter

When water does not drain well or ‘5E’ blinks on the display, clean the debris filter. The product appearance may differ from your washing machine. (However, the cleaning descriptions are the same.)

The descriptions and images in this document may differ from your actual purchased product. For more information, refer to the user manual.

INSTALLING YOUR WASHING MACHINE

1. Open the filter

cover using a coin

or a key.

4. Unscrew the emergency drain cap by turning it counter clockwise.

Installing your washing machine in the location which is slippery

or uneven, will result in vibrations and noise.

If there is too much noise or vibration, check whether the four levelling adjustment legs are evenly and firmly on the floor.

If the washing machine is not level, lift the washing machine

slightly and adjust the lowest of the four levelling adjustment legs.

Before using your washing machine, you must remove the shipping bolts from the back of the unit.

For more information on removing the safety devices, refer to the user manual.

Make sure that the leveling feet legs are level with the floor.

2.

Unscrew the

 

emergency drain

 

cap and pull out the

 

emergency drain

 

tube to drain off the

 

remaining water.

3.

Hold the cap on

 

the end of the

 

emergency drain

5. Clean the debris filter and the inside of the drain hose.

Inside

Debris

filter

6. Replace the debris filter, the emergency drain

LEVELLING YOUR WASHING MACHINE WITH THE LEVELLING FEET

Refer to the descriptions appropriate to your washing machine.

tube and allow all

the water to flow

into a bowl.

cap and tube and then close the filter cover.

Locking nut

 

 

Adjustable nut

 

 

Spanner

1. Level your washer by turning the

2. When your washing machine is

(-) Driver

adjustable nut in and out, as shown

level, tighten the locking nut using

 

 

in the figure.

the (-) driver.

If you open the debris filter when water remains inside the tub, water may flow out.

If the debris filter is assembled incorrectly or not installed, it may cause a water leakage or operating error. Therefore make sure to assemble it correctly.

MAKE SURE YOU KNOW...

Nut

Adjustable feet Spanner

1.Unfasten the locking nut by turning it to the left using a spanner.

2.Level your washing machine by turning the adjustable feet in and out as necessary by hand.

3.Fasten the locking nut by turning it to the right using a spanner.

Adding the

Adding laundry

 

laundry

 

Press the Add laundry(Stop&Add) button and add the laundry when the Add

 

laundry lamp turns on.

 

 

If you add the laundry during a spin cycle, it starts again with the initial set time

 

 

regardless of the remaining time.

 

 

 

 

 

Washing

Wash bedding using only the Bedding course.

Wash

bedding

 

You can wash acrylic, mixed spinning and woolen bedding.

 

individually.

CLEANING THE FILTER

Cleaning the water supply filter

If the filter net is not installed, it may cause a water leakage and operating error. Make sure to install it.

1. Pull and remove the filter net.

2. Clean the filter.

3. Insert the filter net and fasten

 

 

its connector firmly.

When washing general clothes, the washing machine may

not operate in the optimal status.

Wash only one bedding item at a time regardless of size.

Insert bedding rolled up into a ball.

The center of gravity is distributed evenly causing less

vibrations and noise.

Do not wash electric blankets or carpets.

When spinning blankets, cotton bedding, and woolen bedding, too much noise and vibrations may occur and the wash cannot be completed as spinning is not performed.

DC68-02209B_EN_DE_FR_ES_IT_PT_RU.indd 1

 

 

2008-03-19 ¿ÀÈÄ 3:03:50