Sanyo CE27LD4-B instruction manual Menu Operation Analogue channels, Timer

MENU OPERATION - Analogue channels

Many of your TV’s functions are controlled through the menu function.

MENU

Picture	Brightness
	Contrast
	Colour
	Sharpness
	Tint (only if NTSC equipment is detected)
	Text brightness
	Memory
Sound	Volume
	Bass
	Treble
	Balance
	BBE
Timer	OFF Timer
	Alarm Timer
Setting	Child lock		ON/OFF
	AV2		Video/S-video
	Noise Reduction		ON/OFF
Preset	Auto Tuning			Auto		Channel
	Auto sort	Start				Position
	Prog. Preset
	Swap		Semi		Channel
	Fine Tuning
					Position
					Skip
					Memory

During menu operation a bar at the bottom of the screen show which controls can be used.

eg.

Timer

OFF timer

Alarm timer

Press the ubutton to enter and exit the 5 sub menus Picture, Sound, Timer, Setting and Preset.

When a sub menu is selected its options are displayed and its colour will change to yellow.

When you have set each Sub menu you can either press the MENU button to exit and clear the screen or press the 5button until the sub menu is re-selected. Using the 7,8button you can rotate again.

Picture menu

Press the 7or 8button and select Picture menu, set the picture settings for your personal preference.

Picture
Brightness	38
Contrast	42
Colour	19
Sharpness	2
Tint	27
Text brightness	Minimum/Centre/Maximum
Memory	OK? / OK

Use the eor dbutton to select eg. Brightness and the 7or 8 button to adjust levels.

Tint : is only available if NTSC equipment is connected.

Text brightness : you can set to Minimum, Centre or Maximum.

Use the eor dbutton to select and the 7or 8button to set.

To memorise these settings press the F/OK button. (The OK? will change to OK.)

To exit press the MENU button.

Sound menu

Press the MENU button and select Sound menu by pressing the 7 or 8button.

Select and adjust to obtain the best sound settings for your environment using eor dand 7or 8button.

Sound
Volume	12
Bass	0
Treble	0
Balance	0
BBE	ON / OFF

To exit press MENU button.

Timer menu

■Off-timer setting

The Off timer will switch the TV set into the standby mode when the selected time has elapsed.

1.Press the MENU button and select Timer using 7or 8button. Select OFF Timer using the eor dbutton. The complete line turns yellow.

2.Press the 7or 8button to select --:-- (highlighted yellow).

3.Press the eor dbutton to change time.

The time changes in 30 minute steps.The maximum time is 2:00hrs.

4.Press the 7 or 8button to highlight complete line (yellow).

5.Press the OK button to store your settings.

If you have set the off timer, then one minute before the TV switches off, a display appears on the screen.

✐If the TV set is switched off by the standby button on the remote control or by the standby switch on the front of the TV set the timer settings will be cancelled.

Press the MENU button to exit, or press the 7button to highlight complete line yellow and then press the dbutton to set Alarm timer.

Timer	- - : - -	OK?
OFF timer
Alarm timer	- - : - -

■Alarm timer setting

This function can be set so that an alarm goes off. This only hap- pens when the TV is switched on. It may remind you to do something.

1.Press the MENU button and select Timer using the 7or 8 button. Select Alarm timer using the eor dbutton. The complete line turns yellow.

2.Press the 7or 8button to select --:--.

3.Press the eor dbutton to change time.

The display changes in 5 minute steps and the maximum time period is 3:00 hours.

4.Press the 7or 8button to highlight complete line (yellow).

5.Press the OK button to set the Alarm.

When the time period is up, the time up signal will appear on the screen and the alarm will sound for 15 seconds.

To cancel the Alarm timer press any button and the display will disappear.

✐If the TV set is switched off by the standby switch on the remote control, the standby switch on the front of the TV or a power failure occurs the timer settings will be cancelled.

15