Sanyo CE27LD4-B Specification, Plug and Play Helpful hints, Common specification

SPECIFICATION / HELPFUL HINTS

	Specification
Common specification
Power source	AC 220~240V 50Hz
Television system	System I
Colour system	PAL
	(PAL/NTSC3.58 in AV mode)
Channel coverage	UHF:	21-69,
Aerial input impedance	75 ohm
AV terminal
	AV1: CENELEC Standard
	Input: Composite video, RGB and audio-L/R
	Output:TV-output with composite video and
		audio-L/R
	AV2:	CENELEC Standard
	Input: Composite video, RGB, S-VHS and
		audio-L/R
	Output:Monitor-output with composite video
		and audio-L/R
	AV3: CENELEC Standard
	Input: Composite video, and audio-L/R
Side AV terminal
	AV4:	RCA jacks
	Input: Composite video and audio-L/R
Headphone socket	Mini Jack

The following faults are not caused by the receiver:

"GHOSTS"

Reflections of signals from mountains or high buildings will cause multiple images, called "Ghosts". These abnormal conditions can be reduced to minimum by repositioning aerial or by installing new one suited for your area.

"INTERFERENCE"

Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be a temporary condition, but should this interference persist, contact your dealer.

■Plug and Play Helpful hints.

If you do not fit an aerial into this TV set the Plug and Play feature may start up each time you switch on your TV.

To prevent this follow these instructions.

1.Switch on your TV set, the Plug and Play screen appears.

2.Press the MENU button on the remote control to clear the Plug and Play screen.

3.A second screen will appear. Press the Return key to clear from the screen.

4.Press the D/A key to return to Analogue.

5.Press the MENU button to select the Menu screen. (as shown below).

	CE27LD4-B	CE32LD4-B
	CE27LD4BK-B	CE32LD4BK-B
Sound output
(Continuous)	2 x 10W	2 x 10W
Contrast Ratio	900:1	1000:1
Screen(inches)	27	32
(viewing measured diagonally)
Display Resolution	1280 x 720 (WXGA)	1366 x 768 (WXGA)
Viewing angles	H:176°, V:176°	H:176°, V:176°
Dimensions
(WxHxD mm)	800 x 470 x 239	922 x 545 x 239
(including stand)
Weight (kg)	14.4	17.5
(including stand)

Timer

Sound Setting

	Preset
	Auto Tuning	v
Picture	Auto Sort	v
	Prog. Preset	v
	Swap	- -
	Fine Tuning	vv

6.Select Preset Menu by pressing the 1or 2button.

7.Select Prog. Preset by pressing the 6or 5button and enter Semi by pressing the 1button.

8.Press the 6button and select Memory. Press OK button to cancel. (The OK? changes to OK).

Helpful hints

■NO PICTURE, NO SOUND

● Check if TV is plugged in.

● Try a different channel, if OK, probably station trouble.

■POOR PICTURE, SOUND OK

●Adjust BRIGHTNESS control.

●Adjust FINE TUNING control.

●Check aerial connections.

■NO COLOUR, PICTURE OK

● Adjust COLOUR control.

● Adjust FINE TUNING control. ● Is the programme in colour ?

■WEAK PICTURE

●Check aerial connections on back of set.

●Check aerial for broken wires.

●Re-orient aerial.

Semi
Channel	C24
Position	01
Skip	￿ OFF / ON
Memory	OK?

9.The next time you switch on your TV set the Plug and Play screen will not appear.

21