Sanyo DP19241 owner manual To select the video input source, To Select Analog Channels, Enter

NOTE:

• If you press EXIT in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT see your changes.

TV operation

Automatic Search Start

:Select :Adjust

2 Press or to select “Cable” or “Air”.

3 Press or to select “Automatic Search”, then press or ENTER.

4 “Auto Setup” will begin. After the Auto Setup is completed, the TV channel appears on the screen.

• Depending on the reception condition, it may take up to 30 minutes to complete memorizing digital cable channels. Please allow the process to complete without interruption.

Signal Type

Cable

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press POWER (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

to

1 To turn on the TV, press POWER. (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume level will be indicated on the screen by green bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of green bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 20).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS
1-9:		Press 1-9 as needed. Example, to
		select channel 2, press 2, then press
		ENTER.
10-99: Press the 2 digits in order. Example,
		to select channel 12, press 1, 2, then
							ENGLISH
		press ENTER.
TO SELECT DIGITAL CHANNELS
100-135: Press the 3 digits in order. Example, to
		select channel 120, press 1, 2, 0, then
		press ENTER.
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
•	If a channel is selected with only audio content,
•	“Audio only” will be displayed on the screen.
	If a channel is selected with a weak digital
	signal, “Digital channel signal strength is low”
	will be displayed on the screen.
	The same program may be available on either
	an analog channel or a digital channel.You may
•	choose to watch either format.
	If a channel is selected to which you have not
	subscribed, “Digital channel is encrypted” will
	be displayed on the screen.
VHF/UHF/CABLE CHANNELS
	Air				Cable
VHF					VHF
2-13					2-13
UHF				STD/HRC/IRC
14-69			14-36			(A) (W)
			37-59			(AA) (WW)
			60-85			(AAA) (ZZZ)
			86-94		(86) (94)
			95-99			(A-5) (A-1)
			100-135 (100) (135)
			01			(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT

SELECT, then press		or or corresponding
Number buttons (0-4), then press ENTER.You can
select TV, Video, Component, HDMI or PC depending
on which input jacks you used to connect your
devices.
	Input Select
	0.TV
	1.Video
	2.Component
	3.HDMI
	4.PC

[0-4]:Select
CH +/-
Press and release CH + / –. The channel
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on page 20.	17

3FR0321A_En.indd 17

1/7/11 4:32:12 PM