Tractor Contd, Cutter Deck, Productivity | Scag Power Equipment SCR

Section 3

3.3 TRACTOR (CONT'D)

Travel Speed:
Forward	0 - 8.5 MPH
Reverse	0 - 5.0 MPH

3.4 CUTTER DECK

-NOTE-

The machine will travel at 8.5 mph for transport purposes. For best cutting performance the forward travel speed should be adjusted depending upon the cutting conditions.

No. of Blades	3
Width of Cut	48"
Cutter Blades	Three (3) 16-1/2" (P/N 481997) Marbane Blades
Deck Drive	Belt Driven Electric Clutch Connected to a Drive Shaft to a
	Gearbox on the Cutter Deck
Electric Clutch Type	Ogura Electric Clutch
Cutting Height Adjustment	Four Corner Pin Adjustment, 1.5" to 5" in 1/2" increments
Deck Tilt	Manually by Lifting Deck and Engaging Lock Pin
Drive Shaft	Quick-Disconnect Shaft With Two High Speed U-Joints

3.5 GRASS CATCHING SYSTEM

Type	Out-Front Rear Deck Discharge into Blower which discharges
	the Grass Clippings into a Hopper
Hopper	90-Gallon Molded Plastic with Osillating Discharge Chute
Discharge Blower	12" Diameter
Side Discharge	Extra Wide Discharge Opening on the Left Hand Side with Spring
	Loaded Discharge Chute

3.6 HYDRAULIC SYSTEM

Hydraulic Oil Filter	10 Micron Spin-on Element Type
Hydraulic Reservoir	Nylon; 6 Quart Capacity

3.7 WEIGHTS AND DIMENSIONS

Length	95.0"
Tracking Width	42.0"
Overall Width	48.0"
Overall Height	44.0"
Operating Weight	1160 lbs.

3.8 PRODUCTIVITY

The following chart will aid you in determining how many acres your Scag mower will cut per day.

The chart is an estimate based on 8 hours per day cutting time at 4 MPH with an allowance for overlap and turns.

Cutting Width:	48"
Acres Per Day:	21

7

Image 11

Scag Power Equipment SCR manual Tractor Contd, Cutter Deck, Grass Catching System, Hydraulic System, Weights and Dimensions

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction Reference Before Operation Considerations Safety InformationSignal Words Operation Considerations Do not turn sharply. Use care when backing up Maintenance Considerations Install Belt Cover Before Operating Machine Safety and Instructional Decals Tractor SpecificationsEngine Electrical Grass Catching System Weights and DimensionsTractor Contd Cutter Deck Controls and Instrument Identification Operating Instructions Blower Belt Release Safety Interlock System Ground Travel and Steering Starting the Engine Reverse Travel Forward Travel Hillside Operation Engaging the Deck Drive Cutter Blades After Operation HOPPER, Mulch or Side Discharge OperationParking the Mower 10 Tailgate Operation Grass Catching Operation Removing Clogged Material Side Discharge OperationMulching Operation Recommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Deck Locking Pin Locking Pin Hole Tilting the Cutter Deck Condition Cause Cure Troubleshooting Cutting Conditions Scalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause Cure Ground Troubleshooting Contd Parking Brake Adjustment Adjustments Travel Adjustments Neutral Adjustment Start the engine and disengage the parking brake Drive linkage Tracking Adjustment Steering Handle Adjustment Belt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Cutter Deck Adjustments Maintenance Chart Recommended Service Intervals Maintenance Lubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals Contd Lubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelChecking Engine Crankcase Oil Level Filling the Fuel Tank Changing Engine Crankcase OilChanging Engine Oil Filter Engine Fuel System Cleaning and/or Replacing Air Cleaner Element BatteryChecking Electrolyte Level and Cleaning Battery Engine AIR Cleaner Jump Starting Charging the Battery Blade Inspection Blade ReplacementDrive Belts Cutter Blades Checking Lubricant Level TiresHopper Cutter Deck Gearbox 10 Gearbox Drain Plug Power Unit Gearbox 13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Rotating Blades and Belts Replacement Decals and Information Plates SCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999