Neutral Adjustment, Travel Adjustments | Scag Power Equipment SCR

R

Section 6

1/16"

SCR 2K BAR

Spring Housing

Figure 6-3 Brake Actuator Rod Assembly

CAUTION:

Stop the engine and remove the key from the ignition before making any adjustments. Wait for all moving parts to come to a complete stop before beginning work.

CAUTION:

The engine and drive unit can get hot during operation causing burn injuries. Allow engine and drive components to cool before making any adjustments.

Neutral Adjustment

-IMPORTANT-

Before proceeding with this adjustment, be sure that the tire pressure is correct, that the caster wheels turn freely, and that the transmission drive belt tension spring is not broken.

1.Jack up the machine enough to lift the drive wheels and block securely.

2.Pull the speed control lever into the neutral position.

6.2 TRAVEL ADJUSTMENTS

Neutral or tracking adjustments will need to be made if:

A.The speed control lever is in neutral and the machine creeps forward or backward. (Neutral Adjustment)

B.The mower pulls to one side or the other when traveling in a forward direction. (Tracking Adjustment).

If the mower creeps forward or backward as indicated in "A" above, the neutral linkages must be adjusted. Start with adjusting the speed control lever and proceed as directed. To correct the tracking of the mower (mower pulls to one side when traveling in a forward direction), adjust the tracking of the mower as described on page 23.

3.Pull the park brake lever into the fully engaged position.

4.Adjust the speed control lever turnbuckle until the speed control lever contacts the park brake lever and tighten the jam nuts. (See Figure 6-4).

	Speed Control
	Linkage
Speed Control
Lever	No Gap
No Gap
	Brake Lever

SCR 2K CDA

Figure 6-4 Speed Control Lever

22

Image 26

Scag Power Equipment SCR manual Neutral Adjustment, Travel Adjustments

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train Components Before Operation Considerations Safety InformationSignal Words Operation Considerations Maintenance Considerations Do not turn sharply. Use care when backing up Safety and Instructional Decals Install Belt Cover Before Operating Machine Electrical SpecificationsEngine Tractor Cutter Deck Weights and DimensionsTractor Contd Grass Catching System Operating Instructions Controls and Instrument Identification Safety Interlock System Blower Belt Release Starting the Engine Ground Travel and Steering Forward Travel Reverse Travel Engaging the Deck Drive Cutter Blades Hillside Operation After Operation HOPPER, Mulch or Side Discharge OperationParking the Mower Grass Catching Operation 10 Tailgate Operation Removing Clogged Material Side Discharge OperationMulching Operation Recommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Tilting the Cutter Deck Deck Locking Pin Locking Pin Hole Troubleshooting Cutting Conditions Condition Cause Cure Troubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough Contour Troubleshooting Contd Ground Adjustments Parking Brake Adjustment Neutral Adjustment Travel Adjustments Start the engine and disengage the parking brake Tracking Adjustment Steering Handle Adjustment Drive linkage Cutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt Alignment Maintenance Maintenance Chart Recommended Service Intervals Maintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see Figure Lubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelChecking Engine Crankcase Oil Level Engine Fuel System Changing Engine Crankcase OilChanging Engine Oil Filter Filling the Fuel Tank Engine AIR Cleaner BatteryChecking Electrolyte Level and Cleaning Battery Cleaning and/or Replacing Air Cleaner Element Charging the Battery Jump Starting Cutter Blades Blade ReplacementDrive Belts Blade Inspection Cutter Deck Gearbox TiresHopper Checking Lubricant Level Power Unit Gearbox 10 Gearbox Drain Plug BODY, DECK, Hopper and Upholstery 13 Fluid LevelPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Replacement Decals and Information Plates Rotating Blades and Belts SCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999