Hopper | Scag Power Equipment SCR specification

HOPPER

Ref.	Part.		Ref.	Part.
No.	Number	Description	No.	Number	Description
1	04090-02	Pop Rivet, 3/16 x .652	40	422932	Backing Strip, Hinge
2	451193	Guide Weldment, Screen	41	423131	Backing Plate, Door Latch
3	04001-08	Bolt, Hex Head 5/16-18 x 3/4"	42	04003-26 Bolt, Carr. 3/8-16 x 4"
4	481092-01	Plastic Knob, 5/16-18	43	481632	Wheel, Anti-Scalp
5	451191	Screen Weldment	44	04021-05	Lock Nut, 3/8-16
6	451289	Stop Weldment, Screen	45	04001-21 Bolt, Hex Head 3/8-16 x 1-3/4"
7	481972	Hopper	46	04041-07 Flatwasher, 3/8-.391 x .938 x .105
8	481876	Split Ring	47	04019-02 Nut, Serr. Flange 1/4-20
9	43548	Pin, Hopper Latch	48	04003-02 Bolt, Carr. 1/4-20 x 3/4"
10	04060-01	Roll Pin	49	423017	Bracket, Switch Mounting
11	482070	Spring, Door Lock	50	43546	Bushing, Hopper Pivot
12	422872	Mount, Latch Pin	51	04021-09 Nut, Elastic Stop 3/8-16
13	04003-06	Bolt, Carr. 1/4-20 x 1"	52	04001-62 Bolt, Hex Head 3/8-16 x 3-1/4"
14	422978	Support, Hopper Top	53	482071	Strap Bucket Stop
15	04019-02	Nut, Serr. Flange 1/4-20	54	04041-22 Flatwasher, 1/4-.258 x .50 x .0598
16	04091-01	Pop Rivet, 1/4 x .85	55	04019-03 Nut, Serr. Flange 5/16-18

17423178 Retainer Strip, Hopper

1804021-01 Nut, Elastic Stop #10-32

19482184 Latch, Hopper

2004010-11 Screw, #10-32 x 1-1/2"

21482073 Pad, Rubber Heat Deflector

22423130 Backing PLate, Heat Deflector

2304040-14 Flatwasher, 1/4-.312 x .750 x .065

24422037 Mount, Transition Chute Rear

25422228 Mount, Transition Chute Side

26481279 Chute, Transition

2704003-06 Bolt, Carr. 1/4-20 x 1"

28422871 Latch, Hopper Door

2904021-10 Nut, Elastic Stop 5/16-18

30451189 Hinge Weldment, Hopper Door

3104001-126 Bolt, Hex Head 5/16-18 x 5-1/2"

32481092-01 Plastic Knob, 5/16-18

3343547 Pin, Hopper Door

3404060-08 Roll Pin, .188 x 1-1/2"

3504003-12 Bolt, Carr. 5/16-18 x 3/4"

36423128 Bracket, Door Latch

37451190 Hopper Frame Weldment

3804019-02 Nut, Serr. Flange 1/4-20

39481973 Door, Hopper

-NOTE-

Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts

purchased locally are a grade 5.

63

Image 67

Scag Power Equipment SCR manual Hopper

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction Reference Signal Words Safety InformationBefore Operation Considerations Operation Considerations Do not turn sharply. Use care when backing up Maintenance Considerations Install Belt Cover Before Operating Machine Safety and Instructional Decals Tractor SpecificationsEngine Electrical Grass Catching System Weights and DimensionsTractor Contd Cutter Deck Controls and Instrument Identification Operating Instructions Blower Belt Release Safety Interlock System Ground Travel and Steering Starting the Engine Reverse Travel Forward Travel Hillside Operation Engaging the Deck Drive Cutter Blades Parking the Mower HOPPER, Mulch or Side Discharge OperationAfter Operation 10 Tailgate Operation Grass Catching Operation Mulching Operation Side Discharge OperationRemoving Clogged Material Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Deck Locking Pin Locking Pin Hole Tilting the Cutter Deck Condition Cause Cure Troubleshooting Cutting Conditions Scalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause Cure Ground Troubleshooting Contd Parking Brake Adjustment Adjustments Travel Adjustments Neutral Adjustment Start the engine and disengage the parking brake Drive linkage Tracking Adjustment Steering Handle Adjustment Belt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Cutter Deck Adjustments Maintenance Chart Recommended Service Intervals Maintenance Lubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals Contd Lubrication Fitting Points Checking Engine Crankcase Oil Level Checking Hydraulic Oil LevelChanging Hydraulic Oil Filling the Fuel Tank Changing Engine Crankcase OilChanging Engine Oil Filter Engine Fuel System Cleaning and/or Replacing Air Cleaner Element BatteryChecking Electrolyte Level and Cleaning Battery Engine AIR Cleaner Jump Starting Charging the Battery Blade Inspection Blade ReplacementDrive Belts Cutter Blades Checking Lubricant Level TiresHopper Cutter Deck Gearbox 10 Gearbox Drain Plug Power Unit Gearbox 13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Rotating Blades and Belts Replacement Decals and Information Plates SCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999