Manuals / Sea Frost / Kitchen Appliance / Refrigerator

Sea Frost DC 5000 Thermostat Control Panel Location, Electrical Junction Box

Models: DC 5000

1 46

Download 46 pages 60.05 Kb

Page 20

THERMOSTAT CONTROL PANEL LOCATION

The Thermostat Control Panel should be outside the box in order to protect it and to allow observation of the indicator lamp. The length of the sensing tube dictates the location, as it must reach the plate. The maximum length of this tube is 40" (180 mm.) (The sensing tube must be attached to the refrigerator plate in a multiple plate system.) Mount the Thermostat in a location where the wires and sensing tube can be led. Use the cut out template packed with the Thermostat Control Panel. The harness on the Thermostat Control Panel may be spliced with 16-gauge wire.

ELECTRICAL JUNCTION BOX

The DC 5000 is equipped with a 4' (105 cm.) harness that is to connect to the Electrical Junction Box. Do not splice this harness. Position the Electrical Junction Box to allow proper routing of the harness. If the electrical junction box is closer than 4 feet, shorten the harness.

Large battery supply cables, (See wire sizes) the thermostat control harness, and water pump harness will all connect at the electrical junction box.

20

Image 20

Sea Frost DC 5000 installation instructions Thermostat Control Panel Location, Electrical Junction Box

Contents

DC 5000 SYSTEM 134a START UP PROCEDURE AND PERIODIC INSPECTION RFD SIGHT GLASS DETAIL compressor at onceTABLE OF CONTENTS OPERATION GENERAL DESCRIPTIONBREAK-INPERIOD SUGGESTIONS MAINTENANCE ICE MAKINGHARVESTING VERTICAL TRAYS STORAGE OF ICE CUBESCLEANING HOW REFRIGERATION WORKSINSTALLATION ~ WORK HABITS TUBE HANDLINGINSTALLING THE DC 5000 COMPRESSOR UNIT TUBE CUTTINGTUBE BENDING FIT RFD LASTWATER PUMP INSTALLATION AND WATER CIRCUIT The pump will not self-primeThe pump motor must be above the pump body The pump outlet must be above the pump inletABOUT THE PUMP PLATE LOCATIONVALVE UNIT V/U NOTES ON SWAGELOK FITTINGSDRAWING RECONNECTING PRE-SWAGEDFITTINGS SWAGELOK PERFORMANCE RUNNING THE LINESPLANNING POSITIONING THE RFDHELPFUL TOOLS LINE CONNECTION PLANINSULATING THE LINES RFD Receiver Filter DrierMOUNTING THE RFD ELECTRICAL SYSTEM CABLE TIESto leave a sharp end on the cable tie THERMOSTAT CONTROL PANEL LOCATION ELECTRICAL JUNCTION BOXWIRE SIZES WIRING GROUND WIREASSEMBLY INSPECTION CHECK LIST FUSESREFRIGERANT HANDLING AND SAFETY GENERAL SAFETY THIS IS IMPORTANT. READ THISDISCLAIMER REFRIGERANTPROCEDURES FOR WORKING WITH R-134a ACCESS TO THE SYSTEM SERVICE ACCESS PORTSR-134aSERVICE CONNECTING VALVES GAUGESCONNECTING GAUGES DISCONNECTING GAUGESVENTING THE GAUGE SET TAPPING A CAN OF REFRIGERANTVENTING THE CHARGE HOSE LIQUID OR VAPORCOMMISSIONING PROCEDURE EVACUATION WITH A VACUUM PUMPEVACUATION LEAK TEST NEW SYSTEM CHARGING INTRODUCING INITIAL CHARGELEAK CHECKING A CHARGED SYSTEM ABOUT PRESSURES TO LEAK CHECK WITH BUBBLESTO LEAK CHECK WITH AN ELECTRONIC DETECTOR IF A LEAK IS DETECTEDNEW SYSTEM CHARGING READING THE SIGHT GLASS RFD SIGHT GLASS DETAIL PROPER CHARGE AMOUNTGENERAL INFORMATION SPECIAL NOTEcorrected TROUBLESHOOTINGDISCHARGING THE SYSTEM bIf the pressure readings are over 50 psi with the compressor off, proceed to check charge level via sight glass and charge if needed. Charge loss indicates a leak that must be corrected Recharge. Refer to New System Charging Technical helpTOLL FREE IN THE UNITED STATES CANADA, AND CARIBBEANPRESSURE CHARTS PRESSURE CHARTS PRESSURE CHARTS Brushes Leeson Motor DC 5000 MOTOR AND WATER PUMP MAINTENANCELubrication March Water Pump DC5000 WIRING DC 5000 LAYOUT DC 5000 WATER CIRCUIT TWIN VALVE SYSTEMS ONLY Page DC 5000 Low Voltage Protection Relay