Seagate ST3146954FC, ST373554FC, ST336854FC manual Electrical description, Pin descriptions

Models: ST336854FC ST373554FC ST3146954FC

1 98
Download 98 pages 12.01 Kb
Page 78
Image 78
9.5.3Electrical description

9.5.3Electrical description

Fibre Channel drives use the FC-SCA connector for:

DC power

FC-AL interface

Drive select (device identification)

Option selection

Enclosure Services interface

This 40-pin connector is designed to plug directly into a backpanel. External cables are not required.

9.5.4Pin descriptions

This section provides a pin-out of the FC-SCA and a description of the functions provided by the pins.

Table 24: FC-SCA pin descriptions

Pin

Signal name

Signal type

 

 

 

1*

-EN bypass port A

Low Voltage TTL output

2*

12 Volts

 

 

 

 

3*

12 Volts

 

4*

12 Volts

 

 

 

 

5*

-Parallel ESI

 

6*

Ground[1]

 

7*

Active LED out

Open collector out

8*

Reserved

 

 

 

 

9*

Start_1[2]

TTL input

10*

Start_2[2]

TTL input

11*

-EN bypass port B

Low Voltage TTL output

12*

SEL_6

TTL input/output

 

 

 

13*

SEL_5

TTL input/output

14*

SEL_4

TTL input

 

 

 

15*

SEL_3

TTL input/output

16*

Fault LED out

Open collector out

 

 

 

17*

DEV_CTRL_CODE_2[2]

TTL input

18*

DEV_CTRL_CODE_1[2]

TTL input

19*

5 Volts

 

20*

5 Volts

 

 

 

 

Pin

Signal name

Signal type

 

 

 

21

12 Volts charge

 

22

Ground

 

 

 

 

23

Ground

 

24*

+Port A_in

FC Diff. input pair

 

 

 

25*

-Port A_in

 

26

Ground

 

 

 

 

27*

+Port B_in

FC Diff. input pair

28*

-Port B_in

 

 

 

 

29

Ground

 

30*

+Port A_out

FC Diff. output pair

 

 

 

31*

-Port A_out

 

32

Ground

 

 

 

 

33*

+Port B_out

FC Diff. output pair

34*

-Port B_out

 

 

 

 

35

Ground

 

36

SEL_2

TTL input/output

 

 

 

37

SEL_1

TTL input/output

38

SEL_0

TTL input/output

 

 

 

39

DEV_CTRL_CODE_0[2

TTL input

40

5 Volts charge

 

 

 

 

*Short pins in mating backpanel connector.

[1]This pin may be connected to external logic to detect the presence of the drive. The drive connects this pin to the common ground.

[2]Pins 9, 10, 17, 18, and 39 are option select pins and are tied high by the drive circuitry. The preferred elec- trical connection at the backplane is either open or grounded (open for the ‘1’ setting, grounded for the ‘0’ setting). Alternatively, these pins may be driven by a 3.3V logic device, pulled up to 3.3V through a pull-up resistor (recommended size of 10k ohm), or grounded through some other means.

66

Cheetah 15K.4 FC Product Manual, Rev. B

Page 78
Image 78
Seagate ST3146954FC, ST373554FC, ST336854FC manual Electrical description, Pin descriptions