Cheetah 36XL Product Manual, Rev. E

23

6.0Physical/electrical specifications

This section provides information relating to the physical and electrical characteristics of the Cheetah 36XL drive.

6.1AC power requirements

None.

6.2DC power requirements

The voltage and current requirements for a single drive are shown in the following table. Values indicated apply at the drive power connector. The table shows current values in Amperes.

Table 2:

DC power requirements

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

ST336705

 

ST318405

 

ST39205

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Voltage

 

 

 

 

+5 V

 

+12 V

+5 V

 

+12 V

+5 V

 

+12 V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Regulation

 

 

 

[5]

±5%

 

±5%[2]

±5%

 

±5%[2]

±5%

 

±5%[2]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[1][7]

0.71

 

0.50

0.71

 

0.37

0.76

 

0.32

Average idle current DCX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum starting current

 

 

 

 

 

 

 

 

 

 

(peak DC) DC

[1][3]

1.00

 

2.30

1.00

 

2.30

1.00

 

2.30

 

 

 

 

 

 

 

 

 

 

 

Delayed motor start (max) DC

[1][4]

0.58

 

0.03

0.57

 

0.03

0.80

 

0.08

 

 

 

 

 

 

 

 

 

 

 

Peak operating current

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[1][6]

0.81

 

0.75

0.78

 

0.60

0.90

 

0.56

DCX

 

 

 

 

 

 

 

Maximum DC

[1]

0.84

 

0.81

0.82

 

0.69

0.94

 

0.90

Maximum (peak)

 

1.65

 

2.23

1.56

 

1.89

1.78

 

1.91

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes.

[1]Measured with average reading DC ammeter or equivalent sampling scope. Instantaneous current peaks will exceed these values. Power supply at nominal voltage. N = 2, 22 Degrees C ambient.

[2]For +12 V, a –10% tolerance is permissible during initial start of spindle, and must return to ±5% before 10,017 rpm is reached. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator.

[3]See +12 V current profile in Figure 3.

[4]This condition occurs when the Motor Start Option is enabled and the drive has not yet received a Start Motor command.

[5]See Section 6.2.1 “Conducted Noise Immunity.” Specified voltage tolerance is inclusive of ripple, noise, and transient response.

[6]Operating condition is defined as random 8 block reads at 151 I/Os per second. Current and power speci- fied at nominal voltages. Decreasing +5 volts by +5% increases +5 volt current by 4.7%.

[7]During idle, the drive heads are relocated every 60 seconds to a random location within the band from track zero to one-fourth of maximum track.

General Notes from Table 2:

1.Minimum current loading for each supply voltage is not less than 1.2% of the maximum operating current shown.

2.The +5 and +12 volt supplies shall employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak start- ing current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

Page 33
Image 33
Seagate ST318405LW/LC, ST39205LW/LC manual Physical/electrical specifications, AC power requirements, DC power requirements