Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST3320820ACE manual Jumper settings, Master/slave configuration, Cable-select option

Models: ST3320820ACE ST3500830ACE ST3750840ACE ST3250820ACE ST3400820ACE ST3300820ACE

1 52

Download 52 pages 3.56 Kb

Page 31

3.3Jumper settings

3.3.1Master/slave configuration

The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

*Master or single drive

Drive is slave

Master with non ATA- compatible slave

*Cable select

7 5 3 1

8 6 4 2

Figure 4 Master/slave jumper settings

3.3.2Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to determine whether your computer supports this option.

DB35.3 Series PATA Product Manual, Rev. C

23

Image 31

Seagate ST3320820ACE manual Jumper settings, Master/slave configuration, Drive as master with a non-ATA-compatible slave

Contents

DB35.3 Series Pata Page DB35.3 Series Pata Page Contents DB35.3 Series Pata Product Manual, Rev. C List of Figures DB35.3 Series Pata Product Manual, Rev. C Introduction DB35.3 Series Pata Product Manual, Rev. C Specification summary table Drive specificationsDrive specification ST3750840ACE ST3500830ACE ST3400820ACE DB35.3 Series Pata Product Manual, Rev. C Drive specification ST3320820ACE ST3300820ACE ST3250820ACE DB35.3 Series Pata Product Manual, Rev. C Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacity750GB 500GB 400GB 320GB 300GB 250GB Physical characteristicsDrive specification Recording and interface technologySeek time Power specificationsStart/stop times DC power requirements Standby modeConducted noise Typical current profileSleep mode Power-management modesActive mode Idle modeEnvironmental specifications 4 Disc models ShockOperating shock Nonoperating shock Disc modelsFluid Dynamic Bearing FDB motor acoustics AcousticsIdle CE seek profile Agency certification Safety certificationElectromagnetic immunity ReliabilityFCC verification Electromagnetic compatibilityKorean RRL Australian C-Tick N176Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS DB35.3 Series Pata Product Manual, Rev. C Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsCable-select option Jumper settingsMaster/slave configuration Drive as master with a non-ATA-compatible slaveUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view DB35.3 Series Pata Product Manual, Rev. C Pins and supported ATA signals ATA interface signals and connector pinsCommand name Command code in hex Supported ATA commandsF4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit Word0CH Set Features commandCode in features Register A.R.T. command 4 S.M.A.R.T. commandsTechnical Support Warranty ServiceInternet MySeagate Spp.seagate.com Presales SupportData Recovery Services Data Recovery Services Authorized Service CentersCall center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Asia/Pacific support services Index Page Page DB35.3 Series Pata Product Manual, Rev. C Page Seagate Technology LLC