Manuals / Seagate / Computer Equipment / Network Card

Seagate ST3200826SCE, ST3300831SCE, ST3400832SCE, ST3250823SCE Configuring and mounting the drive

Models: ST3250823SCE ST3400832SCE ST3300831SCE ST3200826SCE

1 44

Download 44 pages 54.36 Kb

Page 23

3.0Configuring and mounting the drive

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Keep the drive in the electrostatic discharge (ESG) bag until you are ready for installation.

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

DB35 Serial ATA Product Manual, Rev. E

17

Image 23

Seagate ST3200826SCE, ST3300831SCE manual Configuring and mounting the drive, Handling and static-discharge precautions

Contents

Product Manual ST3400832SCE ST3300831SCE ST3250823SCE ST3200826SCEDB35 Serial ATA Publication number 100362348, Rev. E August 5.0 Seagate Technology support services Contents2.0 Drive specifications 3.0 Configuring and mounting the driveDB35 Serial ATA Product Manual, Rev. E List of Figures Page DB35 Serial ATA 1.0 Introduction1.1 About the Serial ATA interface Drive specifications 2.0 Drive specifications2.1 Specification summary table 30% per hour max Drive specificationsLBA mode 2.3 Default logical geometry2.2 Formatted capacity 2.2.1 LBA modeTypical seek times msec 2.5 Physical characteristics2.4 Recording and interface technology 2.6 Seek timeOperating power and current 2.8 Power specifications2.8.1 Power consumption Spinup powerAverage watts, 25 C DC power requirements2.8.1.1 Typical current profiles Power dissipation typical2.8.3 Voltage tolerance 2.8.4 Power-management modesIdle and Standby timers 2.8.2 Conducted noise2.9.3 Humidity 2.9.3.1 Relative humidity 2.9 Environmental specifications2.9.1 Ambient temperature 2.9.2 Temperature gradient2.9.6.1 Operating vibration 2.10 Acoustics2.9.5.2 Nonoperating shock 2.9.6 VibrationRadio frequency environments 2.11 Electromagnetic immunity2.12 ReliabilityKorean RRL 2.13.1 Safety certification2.13 Agency certification 2.13.2 Electromagnetic compatibility2.14.1 European Union Restriction of Hazardous Substances RoHS 2.14 Environmental protectionAustralian C-Tick N176 2.13.3 FCC verification2.15 Corrosive environment DB35 Serial ATA Product Manual, Rev. E 3.1 Handling and static-discharge precautions 3.0 Configuring and mounting the driveCaution Do not cover, seal, or insert any object into this hole 3.2 Breather filter hole precautions3.3 Configuring the drive Figure 5. Attaching SATA cabling 3.4 Serial ATA cables and connectorsFigure 6. Mounting dimensions-top, side and end view 3.5 Drive mounting4.1 Hot-Plug compatibility 4.0 Serial ATA SATA interfaceSerial ATA connector pin definitions 4.2 Serial ATA device plug connector pin definitionsTable 6 Supported ATA commands 4.3 Supported ATA commandsDB35 Serial ATA Product Manual, Rev. E Command nameCommand code in hex 4.3.1 Identify Device command xxxxH DB35 Serial ATA Product Manual, Rev. Exx07H xx3FHValue DB35 Serial ATA Product Manual, Rev. EWord DescriptionSet PIO mode to default and disable IORDY PIO mode 4.3.2 Set Features commandTable 7 Set Features command values S.M.A.R.T. command 4.3.3 S.M.A.R.T. commandsS.M.A.R.T. commands Code in features registerDB35 Serial ATA Product Manual, Rev. E Internet 5.0 Seagate Technology support servicesSeagate Service Centers Warranty SupportAsia/Pacific Support Services Customer Service OperationsUSA/Canada/Latin America support services Europe, the Middle East and Africa Support ServicesIndex Page Page Page Page Publication Number 100362348, Rev. E, Printed in USA Seagate Technology LLC920 Disc Drive, Scotts Valley, California 95066-4544, USA