Sebo K Vacuum Maintenance, Changing the Filter Bag - Figure, Changing the Exhaust Filter - Figure

VACUUM MAINTENANCE

Always unplug vacuum from outlet

!before dismantling any part of machine!

Changing the Filter Bag - Figure 16

To change the filter bag (45), set the canister upright (as shown in figure 13), press the cover release catch (25) and lower the filter bag cover (26). Grasp the green filter bag sealing plate (46), slide the plate from the holder (48) and push the filter bag cap (47) on to seal the bag. Slide the sealing plate (46) of a new bag into the bag holder slots (48) and push it in firmly until it locks into place. Close the cover, making sure it snaps shut completely. You may find it convenient to store the bag cap inside the filter bag housing below the filter bag. Do not re-use the filter bags. Note: the nature of the contents of the fil- ter bag will affect the point at which it needs changing. Fine dust may require an earlier change even though the bag is not full. Fluff or hair allows air to pass through easily, so the filter bag may overfill before the amber “bag full” light illuminates.

The “bag full or clog” light works correctly only at full power. At lower power levels, the “bag full or clog” light may illuminate incorrectly. Check the status of the filter bag regularly at full power.

Changing the Exhaust Filter - Figure 17

The exhaust filter (51) needs to be changed when it becomes extremely dirty or clogged with dust, or after approximately 10 to 20 filter bags have been used. To change the exhaust filter, set the canister flat on the floor as shown in figure 17. Remove the printed cover on top of the machine (14) by lifting the catch (49) in the upholstery nozzle recess (see inset, figure 17). Pull out the filter using the handle (50) and fit the new filter into the same position. The filter handle should point toward the upholstery nozzle when it is folded down. Fit the tabs on the bottom of the cover (14) into the grooves and snap the cover down firmly.

25

	45
26	26
47
46	48
45
Filter Bag	26
	25
Part # 6629 AM

Figure 16

49
		NO
	LTK3	VULCA
	AIRBEL
	ATT
	2100W
MADEIN	GERMANY
14		50
	51	51

Changing the Micro-Hygiene Filter - Figures 16 &18

After 10 to 20 bags have been used, change the micro-hygiene filter (52). To remove the micro-hygiene filter, set the canister upright (as shown in figure 16). Press the cover release catch (25) and lower the filter bag cover (26). Remove the filter bag, then remove the cover by sliding it up and out of the grooves (53). Pull the old filter out (52) and slide the new filter into the same position. Replace the filter bag, then re-insert the cover by fitting the tabs into the grooves (53) on both sides and sliding it in and down. Push the cover closed, making sure it snaps shut completely.

Changing the AIRBELT - Figure 19

K Filter Set:

Exhaust Filter

and

Micro-Hygiene

Filter

Part # 6696 AM

52

Figure 17

53 53

52

If damage occurs to the AIRBELT cover, it will need to be replaced. To remove the AIRBELT (15), pry off the clip (55) by inserting the tip of a slot-head screw- driver under the bottom side of the clip. Push downward on the screwdriver until the clip pops off. Grasp the end of the AIRBELT cover and pull - the AIR- BELT cover will peel off. The foam bumper (54) remains on the vacuum. To replace the AIRBELT, insert the side ribs of the AIRBELT into the grooves (56). Start at the back, insert rib into one groove (56), and while holding it down, stretch the AIRBELT cover around the foam (54) into the opposite groove (56). Continue around the vacuum. Secure the ends with the clip (55).

SEBO AIRBELT covers are available in a variety of colors and patterns. See your SEBO dealer for available selection.

K Service Box - 10 Filter Bags, Exhaust Filter and Micro-Hygiene Filter

Part # 5828 AM

Figure 18

54

15 55

56

54

56

AIRBELT Cover - Part # 6047 AM/01-08

Figure 19

Note: Never operate the vacuum with incorrectly attached filters or without filters, bag,	9
AIRBELT or filter bag housing cover (26). Do not re-use filter bags. Do not wash and re-use filters.