SECO-LARM USA SK-1123-SQ WIRING, Basic Diagram, Preparing to Program the Keypad, Getting Started

} N.C. dry contact. 50mA max.

Digital Access Keypad Manual

WIRING, BASIC DIAGRAM

Digital Access Keypad Manual

PREPARING TO PROGRAM THE KEYPAD

To program the SK-1123-SQ, first determine the following information:

								Tamper
								OFF
									DAP
								ON
								Tamper	N.C.
								Interlock
								O/P 1	Inhibit
								Door	Sensor
	Relay				Relay			(--)	Ground
								Duress	Output
		1			2
								Keypad	Active
(+)	(--)		Output #1			Output #2		Egress
12-24V	AC/DC	N.C.	COM	N.O.	N.C.	COM	N.O.	In

N.C. Tamper

N.C. Tamper

Interlock -- NPN transistor, used with second keypad1 (-) N.O. O/P #1 inhibit2

(-) N.C. Door position sensor input

(-) Common Ground - for use with interlock function Duress O/P -- Transistor Ground (-) 100mA@24VDC Keypad Active O/P -- Transistor Ground (-) 100mA@24VDC

1.The master code -- Allows the system administrator to program or operate the keypad.

2.The user code or codes -- Allows users to use the keypad's functions.

3.Configuration of the relays and outputs -- For relay output #1 and relay output #2, determine whether the output should operate from 1 to 999 seconds and then turn OFF (momentary mode), or turn ON/ OFF via the code (shunt mode).

4.Result of improper code entry (optional) -- Choose between a 30-second code lockout, duress output, a 15-minute code lockout, or no reaction.

* Note: When X X X X appears in the instructions, it indicates master code entry.

GETTING STARTED

A master code is required to program the keypad. The default master code is set to "0000." To change a forgotten master code, go to page 15 and follow the instructions for "MASTER CODE BYPASS" (DAP jumper).

Once the master code is set, review the programming options and decide exactly what the keypad will do, including the format of the user access codes as well as how the keypad responds via the relay output, buzzer and LEDs. Note that in every case the basic steps for programming are:

1.Enter the master code, followed by the * key, which puts you in programming mode.

2.Enter the programming options defined in the various sections as needed, followed by the # key.

3.Enter the * key again to exit programming mode.

Note: A rapid string of 5 beeps and/or 5 LED flashes indicates an error, while 2 beeps indicates that the entry has been accepted.

EG In - Egress -- N.O., ground (-)3
Relay #2 output -- N.O.		}	1A @ 28VDC, Normally
Relay #2 output -- COM			closed and normally open
Relay #2 output -- N.C.			dry contacts
Relay #1 output -- N.O.			5A @ 28VDC, Normally
Relay #1 output -- COM			closed and normally
Relay #1 output -- N.C.		}open dry contacts
(+)(-)} VAC/VDC12~24	4

1Mantrap control output -- Outputs ground (-) for five seconds after relay output #1 is activated, continues while the door is open.

2Connect to ground (-) to prevent relay output #1 from operating, or to the mantrap (interlock) control output of another keypad to disable output #1 while the other keypad is active.

3Connect to optional N.O. push button or switch.

4For DC, connect to a regulated power supply with correct polarity, + to +, - to -. For AC, polarity is not important.

USER PROGRAMMING

ENTER PROGRAMMING MODE
Enter Master code	Confirm	Function
X X X X	*	Enter into programming mode
Note: For first-time use, Master code is		0 0 0 0

ADDING OR CHANGING MASTER AND USER CODES

WARNING -- Press the correct option key. If the option key is not used and a "0" is pressed after entering the Master

	Code, it could accidentally reprogram the Master Code.
Option	User ID	Access code	Confirm	Function
0		4 to 8 digits	#	Change Master Code
1	00 to 99	4 to 8 digits	#	Set/change up to 100 User Codes for relay output #1, with duress feature
2	0 to 9	4 to 8 digits	#	Set/change up to 10 User Codes for relay output #2

Note: No user code may be the same as the master code.

Note: For User ID, key in the number of the user. For Access Code, type in the code for that particular user.

DELETE A USER

To delete a user who has left the company or who no longer has authority to enter the protected area:

1. Enter programming mode:

Enter Master code		Confirm		Function
X X X X		*		Enter into programming mode
2. Delete code:
Option	User ID	Confirm	Function
			Deletes specific user ID from output #1
1	00 to 99	#
2	0 to 9	#	Deletes specific user ID from output #2

EXIT THE PROGRAMMING MODE BY PRESSING THE "*" KEY

Page 4 SECO-LARM U.S.A., Inc. Page 13