Swivel Mount MZG 415

The swivel mount gives the possibility to use the desk stand together with the microphone clamp or the shock mount for the MKH 406.

Desk Stand MZT 441

The MZT 441 is together with the swivel mount MZG 415 and the

microphone clamp MZQ 415 or the shock mont MZS 415 a stable desk stand for the MKH 406 P 48.

Shock Mount MZS 415

The shock mount can be connected to all tripods, booms, etc. with %" threads and prevents recording being disturbed by footfall for

other strong mechanical disturbances. Diameter 35 mm, Length 80 mm.

Desk Stand MZT 100

This sturdy and stable desk stand with its highly effective sound insulation is especially weil suited to those recording situations in which knocks and handling noise are unavoidable e. g. open debates etc. Used in conjunction with the MZG 415 and the MZQ 415.

Windshield MZW 30

The foam-rubber-windshield should be drawn over the soud inlets

of the microphone when wind disturbances and evident. Largest diameter 60 mm. Length 80 mm. Reduction of wind disturbances approx. 20 dB.

Power Supplies MZN 16 P 48 and MZN 16 P 48-U

Power supply unit for 48V phantom powering according to DIN 45596. The MZN 16 P 48 has been especially designed for the condenser microphones ... P 48 whilst the MZN 16 P 48-U is intended for the condenser microphones ... P 48-U. Two microphones can be

powered simultaneously from each supply unit. Dimensions:

168x 120x50 mm.

Battery adapter MZA 16 P 48 and MZA 16 P 48-U

For voltage supply of phantom powered condenser microphones according to DIN 45596.

Connecting Cable KA 1 und KA 7

Tripie conductor shielded cable fitted with 3-pin standard plug

according to DIN 41 524 and 3-pin standard socket. Suitable for MKH 406 P 48.

Length of cable KA 1: 1.5 m. Length of cable KA 7: 7.5 m.

Connecting Cable KA 7-U

The cable is fitted at one end with a Cannon coupling and at the other with a Cannon plug connector. It is suitable for (e. g.) connecting the MKH 406 P 48-U to the power supply unit MZN 16 P 48-U. Cable length: 7.5 m.

Connecting Cable KA 7 UN

Suitable for all Sennheiser microphones equipped with XLR-connectors (Cannon). The cable is fitted with a 3-pin XLR-connector on one end and a 3-pin screwable standard plug (e. g. T 3260001) on the other end. Length: 7.5 m.

MICROPHONE DIRECTIONNELDE STUDIO MKH 406 P 48

Livraison: 1 microphone
Description abregee

Le MKH 406 P 48 est un microphone directionel de studio Eidirecti- vite cardio'ide. Le microphone fonctionne apres le principe haute frequence et est prevu pour une alimentation Eicircuit fantarne de 40V. Le MKH 406 P 48 se caracterise par sa bande passante large, sa constance concemant les impulsions, sa insensibilite aux frotte- rnents et par sa directivite cardio'ide pratiquement independante de la frequence.

Versions

MKH 406 P 48

Pour alimentation fantarne Ei48 V.Avec fiche normalisee tripolaire vissable (DIN41 524). Surface: nicklee satinee.

MKH 406 P 48-3

Comme MKH P 48, mais avec surface noir mate.

MKH 406 P 48-U

Pour alimentation fantarne Ei48 V.Avec fiche XLRtripolaire. Surface: nicklee satinee.

MKH 406 P 48-U-3Comme MKH 406 P 48-U, mais avec surface noir mate.
Montage haute frequence

Contrairement au montage basse frequence, la capsule d'un micro electrostatique Eihaute frequence presente une faible impedance. A la place de la tension de polarisation relativement elevee, la capsule n'estsoumise qu'Eiune faible tension inferieure Ei 10 volts, foumie par un oscillateur (8 MHz) Eifaible bruit de fond. La faible impedance du systeme mene Eiune haute fiabilite des microphones, particulie- rement au cas des prises de son EiI'exterieur aux conditions climati- ques extremes.

Alimentation et branchement

Tous les micros electrostatiques de Sennheiser electronic avec la designation MKH . . . P 48 and P 48-U sont alimentes par circuit fantarne selon DIN 45596. Le courant passe par les deux conduc- teurs de modulation, le courant de retour par le blindage.

Pour le branchement de ses microphones electrostatiques, Senn- heiser utilise, comme pour les microphones dynamiques, le principe d'adaptation en tension. Cela signifie que I'impedance d'entree de I'amplificateur est beaucoup plus elevee que celle du micro de teile sorte que celui-ci marche presque Eivideo Oe ce fait, ni les variations d'impedance du microphone, ni celles de I'amplificateur n'ontd'in- fluence sensible sur la courbe de reponse. L'impedance de source des microphones electrostatiques Senn heiser Eialimentation fan- tarne est tres faible, environ 10 Q Ei 1000 Hz. La seule exigence

posee Ei I'amplificateur est d'avoir une im.pedance d'entree d'au moins 200Q.

Si toutefois, votre amplificateur presente une impedance inferieure, il faut choisir une resistance additionelle convenant pourque le micro «voie» au moins 200 Q. La division de tension qui en resulte doit evidemment etre prise en consideration. La meme methode est employee si on a besoin d'une impedance micro plus elevee. Dans

ce cas aussi, une resistance additionnelle mene Eiune adaptation correcte.

10

11