Sharp AR-122E, AR-152E 2, 3, 4, 1, 2, 3, 4

19

4

2

Press and hold down the exposure mode

selector key for approximately 5 seconds.

The MANUAL ( ) indicator will go out

and the PHOTO ( ) indicator will begin

to blink. The light and dark indicator

marked "5" will light up, indicating the

standard toner mode is active.

3To enter the toner save mode, press the

light ( ) key. The light and dark

indicator marked "1" will light up,

indicating the toner save mode is

selected.

4Press the exposure mode selector key. The PHOTO ( )

indicator will stop blinking and will light up steadily. The light

and dark indicator marked "3" will light up. The toner save

mode is now active.

USER PROGRAMS

The user programs allow the parameters of certain functions to be set, changed, or

cancelled as desired.

Setting the power save modes, auto clear time, stream

feeding mode and resolution of AUTO & MANUAL mode

1Press and hold down the light ( ) and dark ( ) keys

simultaneously for more than 5 seconds until all the alarm

indicators ( , , , ) blink and " " appears in the

display.

2Use the left copy quantity ( ) key to select a user program

number (1: auto clear time, 2: preheat mode, 3: auto power

shut-off timer, 5: auto power shut-off mode 6: resolution of

AUTO & MANUAL mode). The selected number will blink in the

left side of the display.

3Press the start ( ) key. The entered program number will be

steadily lit and the currently selected parameter number for the

program will blink on the right side of the display.

4Select the desired parameter using the right copy quantity ( )

key. The entered parameter number will blink on the right of the

display.

To return to the standard mode, repeat the procedure but use the dark

( ) key to select exposure level "5" in step 3.

Contents

Main Page 1 CAUTIONS Cautions on using Warning: Caution: Cautions on handling Cautions on laser Proper storage for supplies Trademark acknowledgements CONTENTS 1INTRODUCTION 6 7 2LOADING PAPER 1 4 USING THE MANUAL Conventions used in the manual 5 PART NA MES Single bypass Photoconductive drum Toner cartridge 6 OPERATION PANEL 2 7 PAP ER 8 LOADING THE PAPER TRAY 1 2 3 4 10 BYPASS FEED (including special paper) Print face 1 2 copy (print face down) into the feed slot of the single bypass. Note for loading envelopes 3 11 COPY FLOW 1 Make sure that paper has been loaded in the paper tray (p.8), and check the paper size (p.7). 2 Turn on the unit (p.12). 3 Place the original. 1 2 Power on About the scan head Initial settings of operation panel Power off methods Page 15 SET THE COPY QUANTITY EXPOSURE ADJUSTMENT/PHOTO COPYING Exposure adjustment 1 2 Automatic exposure adjustment 1 2 3 4 17 1 2 select the desired copy ratio. 3 4 18 DESCRIPTION OF SPECIAL FUNCTIONS TONER SAVE MODE 1 2 19 3 4 USER PROGRAMS 2 3 4 20 5 6 DISPLAYING TOTAL NUMBER OF COPIES 1 2 5 21 TONER CARTRIDGE REPLACEMENT 1 2 3 4 5 23 6 TONER CARTRIDGE LIFE 1 2 3 Page Page 6 26 This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING 27 STATUS INDICATORS 28 MISFEED REMOVAL 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 OPTIONAL EQUIPMENT (AL-12PKM) 32 CD-ROM SOFTWARE FOR THE SHARP PERSONAL MFP SERIES MFP driver 33 HARDWARE AND SOFTWARE REQUIREMENTS BEFORE INSTALLATION Flow of installation 35 INSTALLING THE SOFTWARE Installing onto Windows XP (USB/parallel interface) 2 4 5 installed on the screen, and then click the "Start" button. 6 setup (This step will start if it was selected in step 4). 1 7 8 9 10 11 12 Installing onto Windows 98/Me/2000 (USB interface) 2 4 5 6 7 8 1 2 3 4 2 4 5 6 7 setup (This step will start if it was selected in step 4). 6 1 2 8 selected in step 4). 1 2 3 45 INDICATORS ON THE OPERATION PANEL SCANNER indicator ONLINE indicator Start indicator 1 2 3 4 How to print 1 4 media type, and print quality, and then click the "Print" button to start printing. About interrupt copying 48 USING THE SCANNER MODE 1 2 3 4 1 2 3 4 5 Scan Parameter Setting Dialog Box Flow of the Button Manager setting Page 1 2 3 4 Opening the scanner driver and scanning from your computer 1 2 Page 1 2 3 4 5 1 2 3 4 Page 58 USING OTHER INSTALLED DRIVERS 1 2 3 4 5 6 1 2 3 Page 8 61 SPECIFICATIONS Optional equipment Printer/Scanner Expansion Kit (AL-12PKM) Page 64 INDEX A B C M N O P R INDEX BY PURPOSE SOFTWARE LICENSE 2. Restrictions. 3. Termination. 4. Export Law Assurances. 5. Government End Users. 6. Limited Warranty on Media. 7. Disclaimer of Warranty on Software. 8. Limitation of Liability. 9. Controlling Law and Severability. 10. Complete Agreement.