Sharp AR-203E 1, 2

52

MISFEED REMOVAL

When the misfeed ( ) indicator blinks or blinks in the display, the unit will

stop because of a misfeed. If a misfeed occurs when using the SPF, a number may

appear in the display after a minus sign. This indicates the number of the originals

that must be returned to the original feeder tray after a misfeed. Return the required

number of originals. Then this number will disappear when copying is resumed or the

clear ( ) key is pressed. When the SPF misfeeds an original sheet, the unit will

stop and the SPF misfeed ( ) indicator will blink, while the misfeed ( ) indicator

will remain off. For a misfeed of originals in the SPF, see "E: Misfeed in the SPF"

(p.55).

1Open the multi-bypass tray, and side cover, in that order.

To open the multi-bypass tray, see "The multi-bypass tray" (p.10). To open

the side cover, see "TONER CARTRIDGE REPLACEMENT" (p.45).

2Check the misfeed location. Remove the misfed paper

following the instructions for each location in the illustration

below. If the misfeed ( ) indicator blinks, proceed to "A:

Misfeed in the paper feed area" (p.53).

If the unit is turned on with the lower side cover open, the misfeed ( )

indicator will blink. In this case, close the lower side cover. The misfeed

( ) indicator will go out.

If paper is misfed here, proceed to "A:

Misfeed in the paper feed area". (p.53)

If paper is misfed here, proceed to "B:

Misfeed in the fusing area". (p.53)

If the misfed paper is seen from

this side, proceed to "C: Misfeed

in the transport area". (p.54)

If paper is misfed here, proceed

to "D: Misfeed in the lower

paper feed area". (p.55)

Contents

Main AR-203E Page 1 CAUTIONS Caution label on the unit Cautions on using Warning: SOFTWARE LICENSE Caution CONTENTS 1INTRODUCTION 7 2LOADING PAPER 5 1 4 USING THE MANUAL Conventions used in the manual AR-203E 5 PART NA MES 6 OPERATION PANEL 2 7 PAP ER 8 LOADING THE PAPER TRAY 1 2 3 4 10 BYPASS FEED (including special paper) Print face face down) all the way into the multi-bypass tray. 1 2 3 Note for loading envelopes 3 12 COPY FLOW 2 Turn on the unit (p.13). 4 1 2 Power on About the scan head Initial settings of operation panel Power off methods 15 ORIGINAL PLACEMENT Using the original table 1 2 Setting a large original 1 2 Using the SPF 1 2 of originals. 3 original feeder tray. Original face up Peep hole 1 Automatic exposure adjustment 3 4 5 19 REDUCTION/ENLARGEMENT/ZOOM 1 2 select the desired copy ratio. 3 Selecting the tray Press the tray select 4 20 SOFTWARE MFP driver Printer driver 21 BEFORE INSTALLATION Hardware and software requirements Installation environment and usable software Page 7 8 9 10 Installing the Utility Software 11 "Sharpdesk" button. 12 13 14 Connecting a USB cable 1 Using the machine as a shared printer 2 3 4 5 6 7 8 29 INDICATORS ON THE OPERATION PANEL SCAN indicator ONLINE indicator Start indicator Page How to print 1 2 3 4 32 1 Using the Button Manager 2 3 4 1 2 3 4 5 Scan Button Destination Setting Dialog Box Flow of the Button Manager setting Page 1 2 3 4 Opening the scanner driver and scanning from your computer Page 1 2 3 4 5 1 2 3 4 5 VIEWING THE ONLINE MANUAL 5 42 DESCRIPTION OF SPECIAL FUNCTIONS TONER SAVE MODE 1 3 4 USER PROGRAMS Setting the user programs 1 3 4 44 *Factory default settings are indicated with an asterisk (*). 5 will be steadily lit and the entered value will be stored. 6 DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. 6 45 TONER CARTRIDGE REPLACEMENT 1 2 3 4 5 47 6 TONER CARTRIDGE LIFE 1 2 3 48 CLEANING THE UNIT Cabinet Original table and the back side of the original cover and SPF (if installed) Original table/scanning window Original cover/SPF SPF roller SPF scanning window Page 7 50 This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING Problem Possible cause Solution Page 51 STATUS INDICATORS Be sure to use only genuine SHARP parts and supplies. Indication Cause and remedy Page 52 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 5 D: Misfeed in the lower paper feed area 1 2 3 56 Roller DEVELOPER REQUIRED MAINTENANCE REQUIRED Page 8 58 SYSTEM CONFIGURATION SINGLE PASS FEEDER (AR-SP9) 59 1 main unit, the SPF stops and the ZOOM indicator blinks. 2 been scanned from the document feeder tray. 3 1 2 3 4 5 9 61 SPECIFICATIONS Page Single pass feeder (AR-SP9) 250-sheet paper feed unit (AR-D33) 64 ABOUT SUPPLIES AND OPTIONS Supply list Interface cable USB interface cable 65 INDEX 2 A B N O P R S INDEX BY PURPOSE MATERIAL SAFETY DATA SHEET Page : 1/4 1.PRODUCT AND COMPANY IDENTIFICATION 2.COMPOSITION / INFORMATION ON INGREDIENTS MATERIAL SAFETY DATA SHEET Page : 2/4 3.HAZARDS IDENTIFICATION 4.FIRST-AID MEASURES 5.FIRE-FIGHTING MEASURES 6.ACCIDENTAL RELEASE MEASURES MATERIAL SAFETY DATA SHEET Page : 3/4 9.PHYSICAL AND CHEMICAL PROPERTIES 10.STABILITY AND REACTIVITY 11.TOXICOLOGICAL INFORMATION MATERIAL SAFETY DATA SHEET Page : 4/4 12.ECOLOGICAL INFORMATION 13.DISPOSAL CONSIDERATIONS 14.TRANSPORT INFORMATION 15.REGULATORY INFORMATION MATERIAL SAFETY DATA SHEET Page : 1/4 1.PRODUCT AND COMPANY IDENTIFICATION 2.COMPOSITION / INFORMATION ON INGREDIENTS MATERIAL SAFETY DATA SHEET Page : 2/4 3.HAZARDS IDENTIFICATION 4.FIRST-AID MEASURES 5.FIRE-FIGHTING MEASURES 6.ACCIDENTAL RELEASE MEASURES MATERIAL SAFETY DATA SHEET Page : 3/4 9.PHYSICAL AND CHEMICAL PROPERTIES 10.STABILITY AND REACTIVITY 11.TOXICOLOGICAL INFORMATION MATERIAL SAFETY DATA SHEET Page : 4/4 12.ECOLOGICAL INFORMATION 13.DISPOSAL CONSIDERATIONS 14.TRANSPORT INFORMATION 15.REGULATORY INFORMATION A. Information on Disposal for Users (private households) 1. In the European Union 2. In other Countries outside the EU 1. In the European Union 2. In other Countries outside the EU Laserstrahl CLASS 1 LASER PRODUCT LASER KLASSE 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT