Sharp AR-203E 1, 2, 3

59

8

IF A PAPER MISFEED OCCURS IN THE MAIN UNIT

WHEN USING THE SPF

If a paper misfeed occurs in the main unit paper path when making copies with

original(s) through the SPF, the SPF will automatically stop scanning. Manually

remove the misfed paper(s) in the main unit. You can check the number of originals

that must be returned to the document feeder tray in the display on the operation

panel. Follow the steps below to display the number of originals to be returned.

1When a paper misfeed occurs in the

main unit, the SPF stops and the ZOOM

indicator blinks.

The remaining number of sets will blink in the

display.

Be sure to remove misfed paper(s) at the main

unit paper path first. Then follow the step 2

onwards.

2Remove any originals that have not yet

been scanned from the document

feeder tray.

For the original(s) stuck in the SPF, do not

remove manually. This may cause a machine

malfunction. See the step 3.

3Press the copy ratio display (%) key.

The originals that were being scanned in the SPF

will be discharged and the number of original

sheets to be returned will blink in the display.

Place the displayed number of original sheets

back in the document feeder tray together with

the original sheets removed in step 2.

The following procedure omits removal of the misfeed. Be sure to remove

the misfeed before displaying the number of originals to be returned. For

the misfeed removal procedure, see "MISFEED REMOVAL" (p.52).

If "SPF automatic original discharge time" is enabled in the user

programs, the originals in the SPF will be automatically discharged after

the set time elapses. ("USER PROGRAMS" (p.43)

A5 A4

A4 B5

A4 A5

A5 A4

A4 B5

A4 A5

A4

B5

A5

Display of number of original

sheets to be returned

Contents

Main AR-203E Page 1 CAUTIONS Caution label on the unit Cautions on using Warning: SOFTWARE LICENSE Caution CONTENTS 1INTRODUCTION 7 2LOADING PAPER 5 1 4 USING THE MANUAL Conventions used in the manual AR-203E 5 PART NA MES 6 OPERATION PANEL 2 7 PAP ER 8 LOADING THE PAPER TRAY 1 2 3 4 10 BYPASS FEED (including special paper) Print face face down) all the way into the multi-bypass tray. 1 2 3 Note for loading envelopes 3 12 COPY FLOW 2 Turn on the unit (p.13). 4 1 2 Power on About the scan head Initial settings of operation panel Power off methods 15 ORIGINAL PLACEMENT Using the original table 1 2 Setting a large original 1 2 Using the SPF 1 2 of originals. 3 original feeder tray. Original face up Peep hole 1 Automatic exposure adjustment 3 4 5 19 REDUCTION/ENLARGEMENT/ZOOM 1 2 select the desired copy ratio. 3 Selecting the tray Press the tray select 4 20 SOFTWARE MFP driver Printer driver 21 BEFORE INSTALLATION Hardware and software requirements Installation environment and usable software Page 7 8 9 10 Installing the Utility Software 11 "Sharpdesk" button. 12 13 14 Connecting a USB cable 1 Using the machine as a shared printer 2 3 4 5 6 7 8 29 INDICATORS ON THE OPERATION PANEL SCAN indicator ONLINE indicator Start indicator Page How to print 1 2 3 4 32 1 Using the Button Manager 2 3 4 1 2 3 4 5 Scan Button Destination Setting Dialog Box Flow of the Button Manager setting Page 1 2 3 4 Opening the scanner driver and scanning from your computer Page 1 2 3 4 5 1 2 3 4 5 VIEWING THE ONLINE MANUAL 5 42 DESCRIPTION OF SPECIAL FUNCTIONS TONER SAVE MODE 1 3 4 USER PROGRAMS Setting the user programs 1 3 4 44 *Factory default settings are indicated with an asterisk (*). 5 will be steadily lit and the entered value will be stored. 6 DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. 6 45 TONER CARTRIDGE REPLACEMENT 1 2 3 4 5 47 6 TONER CARTRIDGE LIFE 1 2 3 48 CLEANING THE UNIT Cabinet Original table and the back side of the original cover and SPF (if installed) Original table/scanning window Original cover/SPF SPF roller SPF scanning window Page 7 50 This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING Problem Possible cause Solution Page 51 STATUS INDICATORS Be sure to use only genuine SHARP parts and supplies. Indication Cause and remedy Page 52 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 5 D: Misfeed in the lower paper feed area 1 2 3 56 Roller DEVELOPER REQUIRED MAINTENANCE REQUIRED Page 8 58 SYSTEM CONFIGURATION SINGLE PASS FEEDER (AR-SP9) 59 1 main unit, the SPF stops and the ZOOM indicator blinks. 2 been scanned from the document feeder tray. 3 1 2 3 4 5 9 61 SPECIFICATIONS Page Single pass feeder (AR-SP9) 250-sheet paper feed unit (AR-D33) 64 ABOUT SUPPLIES AND OPTIONS Supply list Interface cable USB interface cable 65 INDEX 2 A B N O P R S INDEX BY PURPOSE MATERIAL SAFETY DATA SHEET Page : 1/4 1.PRODUCT AND COMPANY IDENTIFICATION 2.COMPOSITION / INFORMATION ON INGREDIENTS MATERIAL SAFETY DATA SHEET Page : 2/4 3.HAZARDS IDENTIFICATION 4.FIRST-AID MEASURES 5.FIRE-FIGHTING MEASURES 6.ACCIDENTAL RELEASE MEASURES MATERIAL SAFETY DATA SHEET Page : 3/4 9.PHYSICAL AND CHEMICAL PROPERTIES 10.STABILITY AND REACTIVITY 11.TOXICOLOGICAL INFORMATION MATERIAL SAFETY DATA SHEET Page : 4/4 12.ECOLOGICAL INFORMATION 13.DISPOSAL CONSIDERATIONS 14.TRANSPORT INFORMATION 15.REGULATORY INFORMATION MATERIAL SAFETY DATA SHEET Page : 1/4 1.PRODUCT AND COMPANY IDENTIFICATION 2.COMPOSITION / INFORMATION ON INGREDIENTS MATERIAL SAFETY DATA SHEET Page : 2/4 3.HAZARDS IDENTIFICATION 4.FIRST-AID MEASURES 5.FIRE-FIGHTING MEASURES 6.ACCIDENTAL RELEASE MEASURES MATERIAL SAFETY DATA SHEET Page : 3/4 9.PHYSICAL AND CHEMICAL PROPERTIES 10.STABILITY AND REACTIVITY 11.TOXICOLOGICAL INFORMATION MATERIAL SAFETY DATA SHEET Page : 4/4 12.ECOLOGICAL INFORMATION 13.DISPOSAL CONSIDERATIONS 14.TRANSPORT INFORMATION 15.REGULATORY INFORMATION A. Information on Disposal for Users (private households) 1. In the European Union 2. In other Countries outside the EU 1. In the European Union 2. In other Countries outside the EU Laserstrahl CLASS 1 LASER PRODUCT LASER KLASSE 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT