Before you start

Functional overview (cont’d)

Installing batteries in the remote control Using a remote control

Install two “AA” size batteries (supplied), matching their polarity to those indicated inside battery compartment of the remote control.

123

Note

Incorrect use of batteries can result in hazards such as leakage and bursting. Please follow the instruction below.

•Do not mix new and old batteries together.

•Do not use different kinds of batteries together. Although they may look similar, different batter- ies may have different voltages.

•Make sure that the plus and minus ends of each battery match the indications in the battery compartment.

•Remove batteries from equipment that is not going to be used for a month or more.

•When disposing of used batteries, please comply with governmental regulations or public rules for environmental protection that apply in your country or area.

•Do not recharge, short-circuit, heat, burn or dis- assemble batteries.

Keep in mind the following when using the remote control:

•Make sure that there is no obstacle between the remote control and the remote sensor of the unit.

•Remote operation may become unreliable if strong sunlight or fluorescent light is on the remote sen- sor of the unit.

•Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.

•Replace the batteries when you notice a fall-off of the operating range of the remote control.

•The maximum operable range as follows;

Beeline:

approximately 23 feet

 

(7m)

Either side of center: approximately 16 feet

Above:

 

 

 

 

 

 

 

 

 

 

 

 

 

(5m) within 30 degrees

 

 

 

 

 

 

 

 

 

 

 

 

 

approximately 16 feet

Below:

 

 

 

 

 

 

 

 

 

 

 

 

 

(5m) within 15 degrees

 

 

 

 

 

 

 

 

 

 

 

 

 

approximately 10 feet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(3m) within 30 degrees

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The VCR/DVD recorder Switching

Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish to operate with OUTPUT SELECT.

VCR MODE

Press VCR on the remote control. (Verify that the VCR indicator is lit.)

DVD MODE

 

 

OUTPUT SELECT button

 

 

OPEN/CLOSE

STOP/EJECT

PLAY

STOPPLAY

POWER

REC/OTR

CHANNEL DUBBING VCR DVD

REW F.FWD

REC/OTR

 

 

OUTPUT SELECT

Press DVD on the remote control. (Verify that the DVD indicator is lit.)

Note

•Pressing only OUTPUT SELECT on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

•Pressing REC/OTR (DVD) or REC/OTR (VCR) on the remote control switches immediately it’s respective mode so that you can start recording directly on the appropriate media.

 

 

VCR

VCR

DVD

button

 

DVD

DVD

 

indicator

OUTPUT SELECT

button

VCR indicator

VCR/DVD RECORDER

COMBINATION

10