Basic adjustment settings
Power Control
Power control setting allows you to save energy.
Power control for AV sourceNo signal offWhen set to “Enable”, the power will automatically shut down if no signal inputs for 15 minutes.
1 Press MENU and the MENU screen displays.
2 Press c/dto select “Power Control”.
3 Press a/b to select “No Signal Off”, and then press ENTER.
4 Press c/d to select “Enable”, and then press ENTER.
|
|
|
|
|
|
| Enable |
|
| Disable |
|
|
|
|
|
|
|
•Five minutes before the power shuts down, remaining time displays every minute.
NOTE
•“Disable” is factory preset value.
•When a TV program finishes, this function may not operate.
No operation offWhen set to “Enable”, the power will automatically shut down if there is no operation for 3 hours.
1 Repeat steps 1 and 2 in No signal off.
2 | Press a/bto select “No Operation Off”, and |
| then press ENTER. |
3 | Press c/d to select “Enable”, and then |
press ENTER.
• Five minutes before the power shuts down, remaining time displays every minute.
NOTE
• “Disable” is factory preset value.
Power control setting allows you to save energy.
Power managementWhen set, the power will automatically shut down.
1 | Repeat steps 1 and 2 in No signal off. | |||||
2 | Press a/bto select “Power Management”, | |||||
| and then press ENTER. | |||||
3 | Press a/bto select “Mode1” or “Mode2”, | |||||
| and then press ENTER. | |||||
|
|
|
|
|
|
|
|
|
|
|
| Off |
|
|
|
|
|
|
|
|
|
|
|
|
| Mode1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Mode2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Selected item |
|
|
| Description | ||
|
|
|
|
|
| |
Off |
| • No power management | ||||
| • | Factory preset value. | ||||
|
| |||||
|
|
|
|
|
|
|
|
| • | If no signal inputs for 8 minutes, the power | |||
|
|
| shuts down. | |||
|
| • Even if you start using the PC and the signal | ||||
Mode1 |
|
| inputs again, the TV stays off. | |||
| • The TV turns on again by pressing TV | |||||
|
|
| POWER on the remote control unit. (See | |||
|
|
| page 17). | |||
|
| • | Pressing POWER on the TV will have the | |||
|
|
| same result. | |||
|
|
|
|
|
| |
|
| • If no signal inputs for 8 seconds, the TV | ||||
Mode2 |
|
| enters standby mode. | |||
| • | When you start using the PC and the signal | ||||
|
| |||||
|
|
| inputs again, the TV turns on. | |||
|
|
|
|
|
|
|
NOTE |
|
|
|
|
|
|
•When using a digital PC and setting “Mode2” in Power management, the power may not turn back on automatically even if the signal inputs again.
•If you turn off the power by disconnecting AC cord when setting “Mode2” in power management, the TV may not function properly after turning the power on again. In such case, press TV POWER on the remote control unit.
•Pressing POWER on the TV will have the same result.
44