6.Install the hood duct to the oven cavity with the one (1) screw.
7.
8.Connect the wire leads to the fan motor and chassis support, referring to the pictorial diagram.
9.Refer to procedure of "OUTER CASE REMOVAL". And reverse their procedure. And
Table
Shaft
Center of |
bracket |
TURNTABLE MOTOR REMOVAL
1.Disconnect the power supply cord.
2.Open the door and block it open.
3.Remove the three (3) screws holding the base cover to the oven cavity
4.Remove the base cover from the oven cavity by pulling
down and moving to the left slightly.
5.Disconnect the wire leads from the turntable motor.
6.Remove two (2) screws holding turntable motor to the oven cavity.
7.Now the turntable motor is free.
STIRRER MOTOR REMOVAL
1.Disconnect the power supply cord and remove the oven from wall and remove outer case. (Refer to procedure of "Removal of Oven from Wall" and Outer case Removal")
2.Open the door and block it open.
3.Discharge high voltage capacitor.
4.Remove the hood fan motor and the hood duct from the oven cavity, referring to the procedure of " HOOD FAN MOTOR, HOOD DUCT AND OVEN LAMP SOCKET REMOVAL".
5.Disconnect the wire leads from the stirrer motor.
6.Remove the two (2) screws holding the stirrer motor to the waveguide of the oven cavity.
7.Remove the stirrer motor from the waveguide.
8.Now, the stirrer motor is free.
9.When installing the stirrer motor, the shaft of stirrer motor must be inserted to the stirrer fan shaft. Refer to the procedure of "STIRRER COVER AND STIRRER FAN INSTALLATION".
STIRRER COVER AND STIRRER FAN INSTALLATION
1.Put the stirrer fan on the stirrer cover to match the stirrer fan shaft to the center of the stirrer support.
2.Insert the shaft of stirrer fan to the shaft of stirrer motor.
3.Insert the cutout of stirrer cover to the tabs on the ceiling.
4.Install the stirrer cover to the oven cavity, and secure it by one canoe clip.
OVEN LAMP REMOVAL
Shaft
Stirrer Fan
Stirrer Support
Stirrer
Cover
Canoe Clip
1.Disconnect the power supply cord.
2.Remove one (1) screw holding the hood exhaust louver to oven cavity front flange.
3.Remove the hood exhaust louver from the oven by pushing the right and left tabs of the hood exhaust louver. (Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")
4.Lift the oven lamp cover up.
5.Now, the oven lamp and the socket are found.
6.Screw the oven lamp off from the lamp socket.
7.Now, the oven lamp is free.
CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL
1.Disconnect the power supply cord.
2.Open the door and block it open.
3.Remove one (1) screw holding the hood exhaust louver to oven cavity front flange.
4.Remove the hood exhaust louver from the oven by pushing the right and left tabs of the hood exhaust louver. (Refer to procedure of "HOOD EXHAUST LOUVER REMOVAL")
5.Remove one (1) screw holding the control panel to the oven cavity front face plate.
6.Release the control panel from the oven cavity front face plate by lifting it up.
7.Disconnect the wire leads from the relays RY1 and RY2.
8.Disconnect the connectors
9.Remove the control panel assembly from the oven. 10.Now, the control panel assembly is free. 11.Disconnect the connector
key fixing plate.
13.Release the two (2) tabs holding the control unit to the key fixing plate.
14.Now, the control unit is free.
15.Remove the one (1) screw holding the key fixing plate to the control panel.
16.Release the four (4) tabs holding the key fixing plate to
30