Sharp XG-P560W, XG-P560W-N 23

Setting up the Projector Network Environment

5 Click “Internet Protocol Version

4 (TCP/IPv4)”, and click the “Properties” button.

6 Confirm or change an IP address for the setup computer.

1Confirm and note the current IP ad- dress, Subnet mask and Default gateway.

Make sure to note the current IP ad- dress, Subnet mask and Default gate-

way as you will be required to reset them later.

2Set temporarily as follows :

IP address : 192.168.150.3

Subnet mask : 255.255.255.0

Default gateway : (Do not input any values.)

Note

•The factory default settings for the projector are as follows:

DHCP Client : OFF

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

7 After setting, click the “OK” but- ton, and then restart the computer.

After confirming or setting, proceed to “3. Setting up Network Connection for the Pro- jector”.

-23

Contents

DATA PROJECTOR Setting up the Screen Standard Setup (Front Projection) Screen Size and Projection Distance Screen Size and Projection Distance Standard Zoom Lens (AN-P18EZ :Standard Equipment with XG-P560W) F2.5, f=25.5-32mm Fixed Wide Lens (AN-P8EX) F2.5, f=11.6 mm Fixed Wide Lens (AN-P12EX) F2.5, f=17.1 mm Wide-zoomLens (AN-P15EZ) F2.5, f=21.2-25.8mm Tele-zoomLens (AN-P23EZ) F2.5, f=31.9-42.5mm Tele-zoomLens (AN-P30EZ) F2.5, f=40.8-62.8mm Tele-zoomLens (AN-P45EZ) F2.5, f=62.1-97.8mm Connecting Pin Assignments Connecting Pin Assignments Wired Remote Control Terminal Specifications RS-232CSpecifications and Commands RS-232CSpecifications and Commands Commands Page Page Page Page Setting up the Projector Network Environment Setting up the Projector Network Environment 1.Connecting the Pro- jector to a Computer cross-over type Plug the power cord into the AC socket of the projector 2.Setting an IP Address for the Computer 1 Log on the network using the administrator’s account for the computer 2 Click “start”, and click “Control Panel” 4 Click “Properties” Page 3.Setting up a Network Connection for the Projector 1 Start Internet Explorer (version Click the “Apply” button Controlling the Projector via LAN Confirming the Projector Status (Status) Controlling the Projector via LAN (Control) Setting and Adjusting the Projector (Settings & Adjustments) Setting the Security (Network – Security) Making General Settings for the Network (Network – (Network – General) Setting for Sending E-mailwhen an Error Occurs (Mail – Originator Settings) (Mail – Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support – Access URL) Setting the Projector Using RS-232Cor Telnet Setting the Projector Using RS-232Cor Telnet When Connecting Using Telnet 1 Click“start”from theWindows® desk- top and select “Run” 3 Click the “OK” button 4 “User Name:”is displayed. Input the user name and press the “Enter” key SETUP MENU (Main Menu) ADVANCED SETUP MENU Controlling the Projector Using RS-232Cor Telnet Controlling the Projector Using RS-232Cor Telnet Save Settings and Quit ([S]Save & Quit) Quit without Saving Set tings ([Q]Quit Unchanged) IP Address Setting ([1]IP Address) Default Gateway Setting ([3]Default Gateway) Subnet Mask Setting Password Setting ([5]Password) Projector Name Setting ([7]Projector Name) RS-232CBaud Rate Set Disconnecting All Connec tions ([D]Disconnect All) Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) Entering ADVANCED SETUP MENU Setting of Accept IP Address Setting of Search Port (ADVANCED[0]Search Port) Return to Main Menu (ADVANCED[Q]Return to Main Menu) Return to Default Settings Stack Projection Stack Projection Setting up the Stack Projection Basic Projector 1: Master Projector 2: Slave 9 Turn on the projectors first, then turn on the computer Application Projector 1: Projector 2: Video Wall Projection Video Wall Projection Setting up the Video Wall Projection Basic 1 Access one of the four projectors via Internet Explorer 2 Click “Video Wall” on the menu 3 Select “2 X 2” on “Division” 4 Click the assigning button for the desired position Adjusting the Position Horizontally and Vertically Returning to the Default Video Wall Setup 1 Select “1 X 1” on “Division” 2 Click the assigning button Assigning the Projected Image on the Video Wall Setup Notes on the Wide Video Wall Projection Setting up the Video Wall Projection Application Projector 1 : Projector 2 : Projector 3: Projector 4 : ■Preparation Turn on all of the projectors Access the projector 1 from the computer via Internet Explorer Click “Stack” on the menu Select “Master” on “Stack Setting” Make the IP address for each projector as shown below 13 Repeat the same procedure from the step 10 to 12 for the projector 3 and 14 Select inputs as specified in the table on the right Turn off all of the projectors Make connections following the diagram shown on page Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Click “Properties” on the “File” menu Click the “Settings” tab, and then click “ASCII Setup” 9 Send the lamp reset command. “LPRE0001” for LAMP 1 “LPRE0002” for LAMP 10 Close HyperTerminal Troubleshooting Troubleshooting Page Dimensions Projector and Lens Dimensions