Manuals / Sharp / Computer Equipment / Projector

Sharp XG-PH70X-N Remove the lamp unit, Insert the new lamp unit, Replace the lamp unit cover

Models: XG-PH70X-N XG-PH70X

1 110

Download 110 pages 60.6 Kb

Page 100

Image 100

Regarding the Lamp

4 Remove the lamp unit.

•Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

•Be sure that AN-PH7LP1 and AN- PH7LP2 are respective type.

6 Replace the lamp unit cover.

•Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Handle

Securing screws

AN-PH7LP1

AN-PH7LP2

For Lamp 1

Compartment for

AN-PH7LP1

For Lamp 2

Compartment for

AN-PH7LP2

User service screw

-98

Page 100

Image 100

Sharp XG-PH70X-N operation manual Remove the lamp unit, Insert the new lamp unit, Replace the lamp unit cover

Contents

XG-PH70X Model No Serial No Special Note for Users in the U.KIntroduction Product Disposal Buttons used in this OperationContents PreparingUsing Reference For Windows¨ When you want to view the setup manualFor Macintosh¨ Cleaning AccessoriesPower Sources Power-Cord ProtectionRest your eyes occasionally Avoid locations with extremes of tem- peratureUsing the projector in other countries Temperature monitor functionOptional lens installation Do not block the intake and exhaust ventsAccessories Supplied accessoriesOptional accessories CableThrow Distance Optional lensesLens ScreenPart Names and Functions ProjectorAbout the Indicators on the Projector Power indicatorLamp indicators 1 Temperature warning indicatorProjector Side View Input 1 terminalRemote Control Click/UNDO button Mouse/adjustment button 19á56 //\Using the Remote Control When using the remote controlUsable Range Inserting the BatteriesUsing the Remote Control with a Signal Cable Switching the Remote Control ModeUsing the Remote Control as a Wireless Computer Mouse Setup and Projection Quick StartAdjust the angle Setting Up the Projector Setting Up the ProjectorProjecting a Reversed Image Set to FrontConnections INPUT/OUTPUT Terminals and Connectable Main EquipmentYou may need other cables or connectors not listed below Samples of Cables for ConnectionSamples of Cables for Connection Connecting to a Computer Connecting with the RGB CableConnecting with a 5 BNC to 15-pin D-sub Cable Side viewConnecting with a DVI Digital Cable ConnectionsConnecting to Video Equipment Select the input signal type of the video equipment. See Connecting to RGB Video Equipment with a 5 RCA RGB Cable Connections Connecting with an S-video Cable or a Composite Video Cable When connecting to the LAN terminal using a LAN cable Controlling the Projector by a ComputerConnecting to an Amplifier or Other Audio Equipment Connecting to a Monitor That Has an RGB Input TerminalConnecting the Power Cord Turning the Power Off PutTurning the Projector On/Off Turning the Projector OnImage Projection Shifting the LensUsing the Adjustment Feet Press on the projector or on the remote controlWhile lifting the projector, rotate the adjustment feet Lens Shift buttonAdjusting the Projected Image Size Adjusting the FocusZoom button Focus button Focus buttons Zoom buttons Correcting Trapezoidal Distortion Select the type of the keystone correctionPress or to set the posi- tion Geometric AdjustmentMatch screen’s four sides to green test pattern Keystone Adjustment with Press , , \ or to correctImage distortion Press or to set the po- sitionSwitching the Input Mode Input buttonsAdjusting the Volume Press on the remote controlTurning Off the Sound Temporarily Displaying an Enlarged Portion of an ImageSelecting the Picture Mode Press on the remote control to cancel the operationUndo button Picture Mode button Freezing a Moving ImageResize Mode Mouse/adjustment button //\ Undo buttonVideo Displaying and Setting the Break Timer Button AdjustmentDisplaying the Black Screen Black Screen buttonMenu Items Following shows the items that can be set in the projectorMenu Items S. menu Options 1 menu Input 1 / Input 2 / Input 3 Main MenuOptions 2 menu Language menu Status menu Using the Menu Screen Menu Selections AdjustmentsExample Adjusting Bright Example Picture screen menu for Input 1 RGB modeTo adjust the pro- jected image while viewing it Press or to select the item you want to adjustPress \ or to adjust the item selected Single adjustment itemMenu Selections Settings Example Setting OSD DisplaySub menu Press or to select the item you want to setMenu screen will disappear Adjusting the Image Picture Adjustment Picture menuSelect a picture mode before adjusting the im- age Adjusting the Color Temperature Emphasizing the ContrastReducing Image Noise DNR Selecting the Progressive ModeMake sure to set DNR to OFF in the following cases Signal Type Setting Input 1/INPUTSelecting the Color Repro- duction Mode Example C.M.S. screen menu Description of C.M.S. AdjustmentColor Management System C. M. S. menu Selecting the Target ColorSetting the Brightness of the Target Color Setting the Chromatic Value of the Target ColorExample C.M.S. screen menu Description of Brightness Example C.M.S. screen menu Description of Chromatic ValueSetting the Hue of the Target Color Resetting User-defined Color SettingsExample C.M.S. screen menu Description of Reset Example C.M.S. screen menu Description of HueOverview of All Color Set- tings Example C.M.S. screen menuComputer Image Adjustment Fine Sync menu Adjusting the Computer ImageSaving Adjustment Settings Example Fine Sync screen menu for Input 1 RGB modeSelecting Adjustment Set- tings Special Mode SettingChecking the Input Signal Auto Sync AdjustmentDescription of Auto Sync Adjustment Used to automatically adjust a computer imageAuto Sync Display Function Used to set the display during Auto SyncAudio Adjustment Audio menu Adjusting the AudioSetting the Audio Output Type Example Audio screen menu Description of Adjustment ItemsSpeaker Setting Example Audio screen menu Description of Speaker SettingsUsing the Options 1 Menu Setting the Resize ModeExample Options 1 screen menu for Input 1 RGB mode Selectable Items of Resize ModeDescription of OSD Display Settings Setting On-screen DisplayShifting the Projected Im- age Vertically Digital Shift Setting the Video System Capturing Projected ImagesSelecting the Background Image Selecting the Startup ImageEco Mode Detecting the Input Sig- nals AutomaticallyAuto Power Off Function Select System Lock on the OpTions 1 menu, then press Press the 4 buttons on the remoteWhen the System Lock is set Enter the same keycode in Recon- firmWhen the system lock is set If You Forget Your Password Setting a PasswordExample Options 2 screen menu Example Options 2 screen menu Description of Lamp Mode Setting the Lamp ModeChecking the Lamp Life Status Reversing/Inverting Pro- jected Images Description of Stack SettingExample Options 2 screen menu Description of PRJ Modes Shortcut to Make Projector Stack Settings Locking the Operation But- tons on the ProjectorSelect Pair Stack on the Option Menu, and then press Select OK, and then pressSelecting the Fan Mode Example Options 2 screen menu Description of Fan ModeBypassing Unused Input Selections Example Options 2 screen menu Description of Set InputsSelecting the Transmis- sion Speed RS-232C Direct Power On FunctionExample Options 2 screen menu Description of RS-232C Monitor Output Settings LAN/RS232C SettingExample Options 2 screen menu Description of Monitor Out Description of LAN/RS232CDhcp Client Setting TCP/IP SettingExample Options 2 screen menu Description of Dhcp Client Set the TCP/IP manuallyService Mode Enter Gateway using , , and \, then pressOnly the service centers use the menu. Do not use the menu Description of TCP/IPReturning to the Default Settings Selecting the On-screen Display Language Overview of All Menu Set- tingsExample Language screen menu Example Status screen menuMaintenance Cleaning the projectorCleaning the air vents and the intake vent cover Cleaning the lensAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Temperature is Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Insert the new lamp unit Remove the lamp unitReplace the lamp unit cover Resetting the Lamp Timer Connect the power cordReset the lamp timer Reset the lamp timer after replacing the lampComputer Computer Compatibility Chart100 DTV 101Troubleshooting 102Problem Check 103For Sharp Assistance 104Specifications 105Glossary 106Index 107Sharp Corporation