![Shindaiwa Limited Warranty](/images/new-backgrounds/87290/872905x1.webp)
Shindaiwa Limited Warranty
Shindaiwa Inc. manufactures its products to superior standards of quality to ensure customers obtain the highest level of satisfaction. In keeping with this goal, Shindaiwa Inc. warrants the SP518 sprayer to the original purchaser as follows:
Warranty Period
One year from the delivery date to the original purchaser for consumer and commercial applications.
90 days for rental applications.
Warranty Administration
Within the covered warranty period, Shindaiwa Inc. will, at their option, repair or replace any defect in material or work- manship, without charge for parts or labor, if this product is presented at an authorized Shindaiwa dealer.
Warranty Exclusions and Limitations
Shindaiwa Inc. assumes no responsibility for damages, loss, or injury resulting from:
■Normal wear and tear
■Misuse or neglect
■Modifications to or removal of original component parts
Install the Pump Lever and
Connecting Rod
Hitch Pin
Washer
Connecting
Rod
Lever |
|
|
Washer |
|
|
|
| Pump Lever |
Hitch Pin | Washer | Shaft |
|
Install the Shoulder Straps
Slot
Tank
Base
Strap
Hook
Install the straps by fitting the strap hook into the slot in the tank base and then turning it 900 to lock into place.
Adjusting the Shoulder Straps
The warranty is limited to the terms stated herein. Shin- daiwa Inc. disclaims all liability for incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so these limitations may not apply to you.
This warranty give you specific legal rights, and you may also have other rights which may vary from state to state.
Shindaiwa reserves the right to change the design or specifications of this product without obligation to modify previously manufactured products.
1. | Lightly grease the end of the pump lever connecting rod |
| and insert into the upper hole in the pump lever. Secure |
| with flat washer and hitch pin. |
2. | Install a flat washer on the opposite end of the connecting |
| rod. Lightly grease the rod end and insert it into the hole on |
| the top of the pump chamber. Secure with flat washer and |
| hitch pin. |
3. | Install a flat washer on the pump lever shaft. |
4. | Lightly grease the hole on the end of the pump lever and |
| assemble on to the pump lever shaft. Secure with flat |
Tightening
1.Place the sprayer on your back with the staps loosened.
2.Hold the adjustment ring firmly and pull until backpack is secure in place.
Buckle
Adjustment
Ring
Owner’s Responsibilities
The owner of the sprayer must demonstrate reasonable care in the use, maintenance, and storage of this Shindaiwa product. If a warrantable failure should occur, the owner must deliver the product to an authorized Shindaiwa servicing dealer for correction. All residual chemicals must be flushed from the sprayer prior to delivery.
Unidentified chemicals left in the sprayer tank can pose a serious health threat to anyone servicing the unit and unaware of its presence!
To obtain warranty service, proof of purchase must be presented to the authorized Shindaiwa servicing dealer when the product is presented for repairs.
Proof of purchase must include date of purchase and the name and address of the selling dealer.
washer and hitch pin. |
Assembling the Spray Wand
Wand | Screw | Trigger |
| Cap | Valve |
Push the wand into the trigger valve and secure with screw cap. Hand tighten to prevent leakage.
CAUTION!
Do not overtighten!
Loosening
Lift up on the buckle to release tension.
IMPORTANT!
After assembling the sprayer, fill the tank with clear water and lay it on its side. Check for leaks. Return sprayer to its upright position. Pump the lever
Most leaks can be stopped by tightening the appropriate connection or fitting. Any leaks must be stopped prior to filling the sprayer with chemicals.
10 | 3 |