Manuals / Brands / Cell Phone / Cell Phone / Siemens / Cell Phone / Cell Phone

Siemens Mux_guide_v06 4.3.7 Multiplexer close down (CLD) , 4.3.8 Test command (Test)

1 36

Download 36 pages, 1.05 Mb

Multiplexer User's Guide

Confidential / Released

s

mo b i l e

Mux_guide_v06 Page 27 of 36 30.06.2004

Length field:

Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8

EA L1 L2 L3 L4 L5 L6 L7

EA bit: Extension bit.

In the last octet of the sequence the EA bit = 1, otherwise = 0.

If there is only one octet, EA bit = 1 is set.

L-bits: Number of value octets; the following L1 is the LSB, L7 the MSB.

Multiple commands can be sent in a single frame only.

4.3.7 Multiplexer close down (CLD)

Type field:

Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8

1 C/R 0 0 0 0 1 1

Length byte = 0, no value octet

4.3.8 Test command (Test)

The test command is intended to test the connection between MS and TE.

Type field:

Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8

1 C/R 0 0 0 1 0 0

The length byte indicates the number of test bytes sent in the value bytes. The responding

station should answer with exactly the same bit sequence. The test command is used for the

version control. For more detailed information see Chapter 5.

Contents

Main Users Guide Multiplexer User's Guide Multiplexer User's Guide Confidential / Released Mux_guide_v06 Page 2 of 36 30.06.2004 Contents Figures Tables 0 Document history 1 Introduction 1.1 Supported products and related documents 1.2 References 1.3 Term and abbreviations 2 Multiplexer protocol an overview 2.1 Product concept and architecture 2.2 Virtual channels and AT commands 3 Integrating multiplexer into the customer application 3.1 Characteristics 3.1.1 Basic requirements 3.1.2 Restrictions 3.1.3 Dependencies between multiplexer channels and restrictions of use 3.1.4 Functions without channel dependencies 3.1.5 Timing conditions 3.1.6 Operation of a second physical serial interface ASC1 (if applicable) 3.2 Multiplexer control and signaling lines 3.2.1 Flow control Page 3.2.2 Escape sequence 3.3 Power saving 3.4 Bandwidth of logical channels 4 Structure of the multiplexer protocol 4.1 Introduction of the multiplexer protocol 4.2 Data link layer 4.2.1 Flag sequence 4.2.2 Address field 4.2.3 Control field 4.2.4 Length indicator 4.2.5 Information field 4.2.6 Frame checking sequence field (FCS) 4.3 State diagrams Figure 4: Relationship between the customer C and the GSM engine C Customer C Master state machine GSM engine C Slave state machine Customer C GSM engine C Figure 5: MPI Startup, DLC establishment and information transfer Serial interface Customer C GSM engine C Serial i nterface 4.3.1 Start-up procedure 4.3.2 DLC establishment Customer C GSM engine 4.3.3 Information transfer Customer C (Initiator) GSM engine (Responder) Customer C GSM engine 4.3.5 Close-down procedure 4.3.6 Multiplexer control channel Information Field 4.3.7 Multiplexer close down (CLD) 4.3.8 Test command (Test) 4.3.9 Modem status command (MSC) Page 4.3.10 Power saving control (PSC) 4.3.11 Non-supported command response (NSC) Multiplexer User's Guide Confidential / Released 4.4 Example: Establishing logical channels without parameter negotiation Customer C Serial interface GSM engine C Figure 13: Establishing the multiplexer control channel and the logical channel 5 Multiplexer protocol version control 5.1 Introduction 5.2 Multiplexer protocol versions 5.3 Implementing version control 5.3.1 Troubleshooting 5.3.2 Coding of TestCommand message 5.3.3 Example of TestCommand message