Sierra Products EF-4001B Surround Installation, Autolite Installation Instructions

Note - For best insert operation the flexible vent installation should not have any tight bends. Try to achieve a smooth sweep to the vertical rise.

SURROUND INSTALLATION

The surround supplied with the insert is adjustable in height so as to allow for many installation perimeters.

1.After the insert is in position, install left and right surround sides by attaching them to the two side brackets using the four 1/4-20 bolts provided. The retainer nuts on the surround sides m ay be installed at any vertical position to accomm odate the installation.

2.Slide the surround top panel between the hopper top and cover. Push the panel down until the screw holes align with the side legs. Install the (4) #8 screws provided. Install power cord into the receptacle on the right side of the insert. Route cord behind surround leg and out to a ground plus.

AUTOLITE INSTALLATION INSTRUCTIONS

Th e AutoLite System is factory ins talled with the only installation requirem ents being the optional therm ostat.

Figure 7 Connection Panel Lower Right Side

Wall Thermostat Installation:

The wall therm ostat is designed to autom atically regulate the room tem pera ture from the control panel heat setting to the “Off” setting based upon room tem perature. Rem ember to leave the control panel on the "Medium or High" position when utilizing the wall thermostat feature.

The following is a step by step procedure for installing the optional wall therm ostat. Note connection terminals on left side of unit at rear (Figure 7). Use 18/2 thermostat wire for the installation.

a.Unplug heater from wall outlet and 12VDC power!

b. Rem ove factory jump wire and hook up thermostat wires to terminals (Figure 7).

c.Locate thermostat approximately 10 to 12 feet from heater or in area that requires steady temperature.

d. Run thermostat wires from heater to thermostat along wall or under carpet etc. and hook wires to thermostat terminals. On new construction you can, of course, run wire in the walls before sheet rock or paneling is done.

e.Reco nnect AC power.

f.Make sure all wiring is completed before plugging the EASYF IRE Heater back into the wall outlet.

IMPORTANT - Any electrical work performed on the

EA SYFIRE H eater should be done by qualifie d personnel.

Remote Control Thermostat Installation:

Th e re m ote therm ostat is designed to autom atically regulate the room temperature from the control panel heat setting to the “Off” setting based upon room temp erature and place m ent of the rem ote therm ostat. Rem em ber to leave the control panel on the "Medium or High" position when utilizing the wall thermostat feature.

The following is a step by step procedure for installing the optional remote thermostat. Note connection terminals on rear of unit (Figure 7).

a.Unplug heater from wall outlet and 12VDC power!

b. Mount millivolt style remote receiver box to rear of stove using double-sided tape.

b. Rem ove factory jump wire and hook up thermostat wires to terminals (Figure 7).

d. Reconnect AC power and follow instructions with remote thermostat regarding set up.

IMPORTANT - Any electrical work performed on the EASYFIRE H eater should be done by qualifie d personnel.

Autolite Wiring Diagram

DOOR HANDLE ASSEMBLY

The door handle and latch must be assembled and adjusted prior to the operation of the stove.

1.Position handle ass em bly through door and secure with collar by sliding over shaft and tightening with allen wrench provided.

2.Position latch on end of shaft with flat facing allen screw. Depending on gasket, shaft will protrude approx. 1/4" through back of latch collar. Snug allen screw.

Figure 9 Door handle assembly

3.To adjust door, close and turn handle so latc hco ntac ts striker. Door gasket must contact firmly against front face of unit. This can be checked by closing against a piece of paper. Firm ly tug on paper, if it m oves with solid resistance the door is properly adjusted.

4