Switching the device on and off
To supply the device with mains power, place the power switch on the rear panel of the Micro system to the "ON" position. The LED STANDBY lights up.
>To switch the device on press the 
STANDBY button on the device or the 
STANDBY/ON button on the remote control. The Micro system is now operational and the blue background illumination lights up in the display.
>To put the device back into the standby mode press the 
STANDBY button on the device once more or the 
STANDBY/ON button on the remote control.
>The device consumes power in the standby mode. To disconnect the device from mains power move the power switch on the rear panel of the Micro system to the "OFF" position.
Setting the time
You can only adjust the clock in standby mode. The program- ming for the time is not retained if the device is disconnected from the power network or switched off with the power switch. If, during the setting, approx. 10 seconds elapses without a button being activated the device changes to the standby mode and the settings must be carried out again.
>Press and hold the
> Press the button SKIP/SEARCH or SKIP/SEARCH
on the device and/or on the remote control to set the time to 24 hour or 12 hour display.
>Press the
> Press the button | SKIP/SEARCH or | SKIP/SEARCH to |
set the hour. |
|
|
>Press the
> Press the button | SKIP/SEARCH or | SKIP/SEARCH to |
set the minutes. |
|
|
>Press the
>For this press repeatedly the FUNCTION button on the device or on the remote control until the desired operation mode is shown in the display.
Setting the sound volume levels
>To increase the volume press or hold the VOL + button on the device and/or VOLUME + on the remote control until the desired volume is reached.
>To decrease the volume press or hold the VOL - button on the device and/or VOLUME - on the remote control until the desired volume is reached.
>To switch the sound to mute, press the button 
MUTE on the remote control.
>To switch the sound back on press the 
MUTE button once more or one of the buttons VOL + or VOL
Setting the sound quality
The Micro system is equipped with several sound settings (CLASSIC, ROCK, POP, JAZZ), which you can access accord- ing to the currently playing music.
>For this press repeatedly the EQ button on the remote con- trol until the desired sound setting is shown in the display.
With the initial pressing of the EQ button the current setting (PASS) is shown. PASS stands for "Passive" (neutral).
Using headphones
You can connect headphones to the Micro system with a 3.5mm jackplug (not supplied). The headphones socket is located on the front of the Micro system. When you have connected the headphones, the loudspeakers are disconnected and you will only hear sound via the headphones.
Attention! Listening to music with headphones for long periods and at high sound volume levels can lead to hearing damage!
Selecting mode of operation
You can select from the following modes:
• CD | - Playback of audio CDs or MP3/WMA CDs |
• USB | - Playback of MP3/WMA files on a USB |
| data carrier |
• RAD | - Playback of radio stations |
• LINE | - Playback of audio sources through the LINE |
| IN connection. |
• TAPE | - Playback of audio cassettes |
Operating the radio
This device receives radio stations on the frequency bands, Ul- tra short wave (USW or engl. FM) and Medium wave (MW or engl. AM).
>In order to receive a good VHF reception with the Micro system unwind the dipole antenna on the rear panel of the device completely.
>Should FM radio reception be inadequate, change the position of the wire antenna. Secure the dipole antenna, if necessary, with sticky tape.
>The device has a built in ferrite antenna for reception of MW stations. When the MW reception is insufficient turn the device in a more favourable direction.
>Switch the Micro system on with the 
STANDBY button on the device or with the 
STANDBY/ON button on the remote control.
- 5 -
