Simplicity 1693120 Operating the Tractor, Starting the Engine, Stopping the Tractor Engine

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

STARTING THE ENGINE

Gas Models

1.While sitting in the operator’s seat, fully depress the brake pedal or set the parking brake.

2.Set the cruise control lever in neutral and make sure that your feet are not depressing the ground speed control pedals.

3.Disengage the PTO clutch(s).

4.Set the throttle to FULL.

5.Pull the CHOKE knob out to choke the engine.

NOTE: A warm engine may not require choking.

6.Insert the key into the ignition switch and turn it to

START.

7.After the engine starts, move the engine throttle con- trol to SLOW. Warm up the engine by running it for at least a minute before engaging the PTO switch or dri- ving the tractor. Push Choke Knob in after engine has warmed.

Diesel Models

1.While sitting in the operator’s seat, fully depress the brake pedal or set the parking brake.

2.Set the cruise control lever in neutral and make sure that your feet are not depressing the ground speed control pedals.

3.Disengage the PTO clutch(s).

4.Set the throttle to middle position (set throttle to FULL when starting in cold weather).

5.Turn the key to the RUN position to activate the glow plugs (the glow plug light in the dashboard display will light).

6.Wait for the glow plug light to turn off, then turn the key to START. If the engine does not start immedi- ately, move the throttle to FULL.

7.After the engine starts, move the engine throttle con- trol to SLOW. Warm up the engine by running it for at least a minute.

8.Move the throttle to FULL before engaging the PTO switch or driving the tractor.

NOTE: In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For nor- mal engine shut down follow the procedure given in

STOPPING THE TRACTOR.

Operating the Tractor

STOPPING THE TRACTOR &

ENGINE

1.Setting the cruise control to neutral and taking your foot off the ground speed control pedals will stop tractor movement. For emergency stopping depress the brake pedal.

2.Engage the parking brake.

3.Disengage the PTO.

4.Throttle the engine down to approximately 2200 RPM and turn the ignition key to OFF. Remove the key.

NOTE: Stopping the engine at speeds lower than approximately 2000 RPM can cause engine damage. Do not stop the engine with the throttle control in the IDLE position.

DRIVING THE TRACTOR

1.Sit in the seat and adjust the seat and steering wheel so that you can comfortably reach all the controls and see the dashboard display.

2.Engage the parking brake.

3.Make sure all PTO switches are disengaged and the cruise control lever is in neutral.

4.Start the engine (see STARTING THE ENGINE).

5.Disengage the parking brake and release the brake pedal.

6.Depress the forward ground speed control pedal to travel forward. Release the pedal to stop. Note that the further down the pedal is depressed the faster the tractor will travel.

7.Stop the tractor by releasing the ground speed con- trol pedal, setting the parking brake, and stopping the engine (see STOPPING THE TRACTOR AND ENGINE).

MOWING

1.Engage the parking brake. Make sure all PTO switches are disengaged and the cruise control lever is in neutral.

2.Start the engine (see STARTING THE ENGINE).

3.Set the mower cutting height.

4.Lower the attachment lift.

5.Set the throttle to FULL.

6.Engage the front PTO (Mower Deck).

7.Begin mowing. See Section C for tips on mowing patterns, lawn care, and trouble shooting informa- tion.

8.When finished, shut off the front PTO and raise the attachment lift.

9.Stop the engine (see STOPPING THE TRACTOR AND ENGINE).

13