Simplicity 24HP manual Troubleshooting, Adjustments, & Service, Troubleshooting Warning

Models: 24HP

1 45
Download 45 pages 63.1 Kb
Page 33
Image 33
Troubleshooting, Adjustments, & Service

Troubleshooting, Adjustments, & Service

TROUBLESHOOTING TROUBLESHOOTING WARNINGWARNING

While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.

The troubleshooting guide below lists the most common problems, their causes and remedies.

See the information on the following pages for instructions on how to perform most of these minor adjustments and service repairs yourself. If you prefer, all of these procedures can be performed for you by your local authorized dealer.

To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

Troubleshooting

TROUBLESHOOTING THE RIDER

PROBLEM

CAUSE

REMEDY

Engine will not turnover or start.

1.

Parking brake not engaged.

1. Engage parking brake.

 

2.

PTO (electric clutch) switch

2. Place in OFF position.

 

 

in ON position.

 

 

3.

Out of fuel.

3. If engine is hot, allow it to cool, then refill

 

 

 

the fuel tank.

 

4.

Engine flooded.

4. Move choke control to closed position.

 

5.

Fuse blown.

5. Replace fuse.

 

6.

Battery terminals require

6. Clean the battery terminals

 

 

cleaning.

 

 

7.

Battery discharged or dead.

7. Recharge or replace.

 

8.

Wiring loose or broken.

8. Visually check wiring & replace broken or

 

 

 

frayed wires. Tighten loose connections.

 

9.

Solenoid or starter motor faulty.

9. Repair or replace. See authorized dealer

 

10.

Safety interlock switch

10. Replace as needed. See authorized

 

 

faulty.

service dealer.

 

11.

Spark plug(s) faulty, fouled

11. Clean and gap or replace.

 

 

or incorrectly gapped.

See engine manual.

 

12.

Water in fuel.

12. Drain fuel & replace with fresh fuel.

 

13.

Gas is old or stale.

13. Drain fuel & replace with fresh fuel.

 

 

 

 

Engine starts hard or runs poorly.

1.

Fuel mixture too rich.

1. Clean air filter. Check choke adjustment.

 

2.

Spark plug faulty, fouled, or

2. Clean and gap or replace.

 

 

incorrectly gapped.

(See engine manual.)

 

 

 

 

Engine knocks.

1.

Low oil level.

1. Check/add oil as required.

 

2.

Using wrong grade oil.

2. See engine manual.

 

 

 

 

Excessive oil consumption.

1.

Engine running too hot.

1. Clean engine fins, blower screen and

 

 

 

air cleaner.

 

2.

Using wrong weight oil.

2. See engine manual.

 

3.

Too much oil in crankcase.

3. Drain excess oil.

 

 

 

 

Engine exhaust is black.

1.

Dirty air filter.

1. Replace air filter. See engine manual.

 

2.

Engine choke control

2. Open choke control.

 

 

is in closed position.

 

30

www.simplicitymfg.com www.snapper.com

Page 33
Image 33
Simplicity 24HP manual Troubleshooting, Adjustments, & Service, Troubleshooting Warning, Troubleshooting The Rider