Sioux Tools 5202 manual Model

Model 5202

Micro Polisher

IMPORTANT

Form # ZCE539

Date 2-02/A

Read these instructions carefully before installing,operating, servicing or repairing this tool. Keep these instructionsin a safe accessible place.

1	SAFETY MESSAGES		1	A WARNING					Operator Instructions
	Personal Safety Equipment		I	Always Read Instructions Before				1	Includes:
1Use -Safety Glasses		YES		0 Using PowerTools					Safety Rules
Use - Safety Gloves		YES		@ Always Wear Safety Goggles					ores seen	U s e
Use - Safety Boots				@ Wear Hearing Protection					Work Stations
									Putting Into Service
Use - Breathing Masks		YES
				Avoid Prolonged Exposure					Operating
Use - Ear Protectors
				ffs^ To Vibration					Dismantling and Assembly
	Safety rules when using a 5202 Micro Polisher
- Use accessories rated at least 5,500 RPM.						local, regional or country legal requirements when
-	Prolongedexposure to vibration may cause injury.				-	installing, using or maintainingthe tool.
-	Readall instructionsbeforeusingthis tool. All operators must					Take care that the exhaustair does not point towards any
-	be fully trainedin its useand aware of these safety rules.					other person or material or substance that could be
	Do not exceed the maximum working air pressure.					contaminatedby oil droplets.When first lubricatinga tool
-	Use personal protection equipment as recommended.					or if the tool exhaust has a high oil content, do not allow
-	Some dust created by power sanding, sawing, grinding,				-	the exhaustair to come near very hot surfaces or flames.
	drilling, and other construction activities contains					Never lay the tool down until the working attachment has
	chemicals knownto cause cancer, birthdefectsand other					stopped moving.
	reproductive harm.				- When the tool is not in use, shut off the air supply and
- Use compressedair only at the recommendedconditions.						press throttle triggerllever to drain the supply line. If the
-	If the tool appears to malfunction, remove from use					tool is not to be used for a oeriod of time. first lubricate.
	immediatelyand arrange for service and repair. If it is not					disconnectfrom air supply and store in a dry average room
	practicalto removetool from service, then shut off the air				-	temperature environment.
	supply to the tool and write or have written a warning					If the tool is passed from one user to a new or inexperi-
	note and attach it to the tool.					enceduser, make sure these instructionsare available to
-	If tool is to be used with a balancer or other suspension				-	be passed with the tool.
	device, ensure that the tool is firmly attached to the					Do not remove any manufacturer fitted safety devices
-	suspensionlsupportdevice.					where fitted, i.e.,			wheel guards, safety trigger, speed
	When operating the tool, always keep the body and				-	governors, etc.
	articularly the handsaway from the working attachment					Wherever possible,secure workpiece with clamps, a vise,
-	I'ixed to the tool.					etc. to make it rigid so it does not move during the work
	The tool is not electrically insulated. Never use the tool if					operation. Keep good balance at all times. Do not stretch
	there is any chance of coming into contact with live				-	or overreach.
	electricity.					Try to match the tool to the work operation. Do not use a
- Always when using the tool, adopt a firm footing and/or						tool that is too light or heavy for the work operation. If in
	position and rip the tool sufficiently only to overcome				-	doubt, seek advice.
	any reaction krces that may result from the tool doing					In general terms, this tool is not suitable for underwater
-	work. Do not overgrip.					useor usein explosive environments -seek advice from
	Use only correct spare partsfor maintenanceand repair.					manufacturer.
	Do not improvise or make temporary repairs. Major				- Try to make sure that the work area is clear to enable the
	servicing and repairs should only be carried out by					work task to be performed safely. If practical and
	personstrained to do so.					possible, try to clear unnecessary obstructions before
-	Do not lock, tape, wire, etc. the 'OnIOff'valve in 'On'				-	starting work.
	position.The throttletriggerllever,etc. mustalways be free					Always use air hose and couplings with minimum work-
-	to return to the 'Off' positionwhen released.					ing pressure ratings at least 1 112 times the maximum
	Always shut off the air supply to the tool and press the					working pressure rating of the tool.
	'OnlOffvalve to exhaust the air from the feed hose
	beforefitting, removingor adjustingthe									-
	working attachmentfitted to the tool.								Take Air From Top
- Before usingthe tool, make sure that a
				All Pipe And Fittings							A
	shut off device has been fitted to the
				Should Be 112"Or Larger						Low Spot To
	supply line and the position is known			Compressor
	and easily accessible so that the air									Trap Water
				with Sufficient Capacity
	supply to the tool can be shut off in an
				To Maintain Recommended 11			11
-	emergency.
	Checkhoseandfittingsregularlyforwear.			Working Pressure At
- Take care against entanglement of the
	movingpartsof the toolwithclothing,hair,
	ties, cleaningrags, rings,jewelry, watches,									Drain Daily
	bracelets, etc. This could causethe body
	or partsof the body to be drawn towards									L
	andincontactwiththe movingpartsofthe
	tool and could be very dangerous.
- It is expectedthat users will adopt safe				Recommended Air Supply System						Figure 1
	working practices and observe all

Page No 1