E
N G L I S H

THE POWER UNIT'S OPERATION - PE

The electric / hydraulic edge-o-dock leveler utilizes an electric motor directly coupled to a gear-type hydraulic pump to produce the needed fluid pressure and flow to allow the cylinder(s) to perform the work of lifting the dockplate.

A hydraulic manifold houses the hydraulic control components, and is bolted directly onto the gear pump. The power unit's hydraulic components are all rated for 3,000 psi working pressure.

Important parts of power unit included:

The electric motor. Motors are available for operaton on single- or three-phase AC supplies (all are dual-voltage capable.)

The gear pump. Its shaft is coupled directly to the shaft of the electric motor.

The check valve. Its purpose is to prevent the backflow of fluid through the pump.

The pressure relief valve. Its job is to open a path for fluid to flow back to the reservoir in the event that the fluid pressure built up by the pump exceeds 1,500 psi. Thus the system cannot see more than 1,500 psi.

The pilot-operated check valve. This is a hydraulically-operated cartridge valve. It closes to allow oil flow to the cylinder(s) when the system is under pressure, then opens to allow the levelers lip to fall when the system pressure drops after the motor turns off.

The pressure-compensated flow control. This regulates the fluid flow from the cylinder(s) back to the reservoir when the pilot-operated valve opens. It allows for the adjustment of the lip fall rate.

The hydraulic lift cylinders(s).

The hydraulic fluid. The system uses HO150 hydraulic fluid. Any anti-wear hydraulic fluid with an SUS viscosity of 150 - 200 at 100°F (SAE viscosity grade of 32) such as AW-32 or Dextron transmission fluid are acceptable.

When the leveler is to be extended, the operator presses the "RAISE" pushbutton. The motor turns, and in turning it spins the hydraulic gear pump. Oil is drawn from the reservoir and into the pump. System pressure builds and causes the pilot-operated check valve to close.

Once the lip extends out, the operator releases the pushbutton. The check valve prevents oil from from returning to the reservoir through the pump. When the pressure in the hydraulic system drops sufficiently, the pilot-operated check valve opens to allow the oil in the cylinder(s) to return back to the reservoir through the pressure-compenated flow control valve, which will regulate the rate at which the lip lowers.

In the event that the lip won't raise, it will be necessary to remove the pilot-operated check valve for inspection and cleaning, as follows:

• Secure the lip plate in the extended position to allow access to the power unit.

Disconnect and lock out the leveler's power supply

Remove the cartridge valve from the cavity marked POCV.

Inspect for contaminants in the valve or the valve cavity.

Wash the valve in mineral spirits or kerosene if possible. Blow off the valve with a compressed-air gun.

Replace the valve and cycle the leveler several times.

Troubleshooting Guide for "PE" Series

Only qualified individuals trained to understand mechanical devices and their associated electrical and hydraulic circuits should attempt troubleshooting and repair of this equipment.

Care should be taken to identify all potential hazards and comply with applicable safety procedures before beginning work.

Consult the factory for problems at time of installation, or for any problems not addressed below.

Before working on the power unit, always secure the lip plate outward and disconnect the power supply.

PROBLEM

POSSIBLE CAUSE

Lever doesn't cycle when the

Motor doesn't run

"RAISE" button is pressed.

 

CORRECTIVE ACTION

Use a multimeter to check: for proper supply (all legs) and control voltage; for an "open anywhere in the control circuit.

Visually check for loose wiring or pushbutton components.

Motor runs properly, but the deck doesn't move or the lip doesn't extend. Motor and pump not noisy.

Verify the motor shaft rotates CCW.

Ensure that the reservoir is full and that its fill hole plug has been replaced by a breather plug.

Check for items resting on the leveler.

Install a pressure gauge to check hydraulic system pressure. If it doesn't build to 1,500 psi, consult the factory for a replacement pump.

Leveler raises but won't lower, or lowers only slowly.

Remove, check and clean the pilot-operated check valve.

Remove, check and clean the pilot-operated check valve and the flow control valve.

Check for any binding of the mechanical parts; hinge, etc.

7

Page 7
Image 7
Skil FM Series, PP Series owner manual Power Units Operation PE, Troubleshooting Guide for PE Series

PE Series, PP Series, FM Series specifications

Skil Power Tools has long been recognized for delivering innovative and reliable equipment tailored for both professional and DIY enthusiasts. The Skil FM Series, PP Series, and PE Series exemplify the brand's commitment to efficiency, performance, and user-friendliness.

The Skil FM Series is particularly well-regarded for its advanced features in the realm of portable and compact power tools. This series often includes versatile tools such as cordless drills and saws, specifically designed for ease of use and mobility. Key characteristics of the FM Series involve lightweight designs, ergonomic grips, and the latest battery technologies. Many tools in this series are equipped with lithium-ion batteries that provide long-lasting power and quick recharge capabilities, enabling users to work without interruption. Additionally, the FM Series often boasts integrated LED lights, making it easier to work in low-light conditions.

Next, the Skil PP Series is tailored towards precision and performance, ideal for woodworking and intricate projects. This series often includes routers, jigsaws, and oscillating multi-tools. The standout feature of the PP Series is its precision engineering, which ensures that every cut and finish presents a professional touch. These tools often incorporate variable speed settings, allowing users to customize their approach based on the material and task at hand. Another essential aspect of the PP Series is the inclusion of advanced dust extraction systems, which contribute to cleaner work environments and enhanced visibility during intricate operations.

Lastly, the PE Series focuses on outdoor power equipment. This includes tools like lawnmowers, string trimmers, and leaf blowers. The PE Series emphasizes durability and performance in various outdoor conditions. A notable feature is the integration of eco-friendly technologies, such as electric motors that reduce emissions and noise levels. These tools are designed with sturdy yet lightweight materials for ease of maneuverability, and many come with adjustable cutting heights and various speed settings to optimize performance based on user needs.

In summary, the Skil FM, PP, and PE Series each serve distinct user needs while providing advanced technologies, ergonomic designs, and reliable performance. Whether for indoor renovations, precision woodworking, or outdoor maintenance, Skil continues to innovate and engineer tools that cater to the diverse demands of users, enhancing productivity and overall experience.