4. INSTALLATION (CONT)
One of
Vertical
Supports
Door closed | Door open |
8. LOSS OF SIGNAL INDICATION
When the battery level on the sensor drops to a certain level, or the sensor is out of the operating range, the receiver will show a “loss of signal” indication. The red LED representing that zone will flash rapidly, i.e. if zone 1 sensor is lost, the zone 1 red LED will flash rapidly.
When the loss of signal indication occurs, move the receiver closer to the corresponding sensor and trigger that sensor. If the red LED stops flashing rapidly, that means the receiver or sensor needs to be relocated. If the “loss of signal” indication persists, replace the battery of that sensor.
Step 2 – Mount the sensor onto your garage door
You can mount the sensor onto your garage door with
For w ooden garage doors, it is recommended |
|
to mount the sensor with screws onto the | 4 Screws |
garage door with 3 x 18 screws provided. |
|
9. OTHER HOUSEHOLD ALERT ® SENSORS
The Household Alert® receiver can work with up to 4 different sensors: garage door monitor sensors, door / window sensors, water sensors, indoor/outdoor motion sensors, etc. Please visit www.skylinkhome.com or contact us at support@skylinkhome.com for more information of how to fully utilize your Garage Door MonitorTM.
Note:
When the garage door is opening/closing, make sure the sensor does not interfere with the safety reversing sensor or safety beam sensor supplied with your existing garage door opener.
Note: Ensure you straighten up the antenna |
|
|
|
|
|
|
1/2 Inch |
|
|
| |||
on the receiver to receive the best possible |
|
|
| |||
|
|
|
|
|
| |
reception. |
|
| Diagram A | |||
5. OPERATION
When the garage door is open, the sensor will send a signal to the receiver. It will beep and the corresponding zone red LED will flash.
If the sensor is set to zone 1, zone 1 red LED on the receiver will flash, and the receiver will emit a continuous “single beep”, i.e. “beep” pause, “beep”, pause….. etc.
If the sensor is set to zone 4, zone 4 red LED will flash, and the receiver will emit a
By the number of beeps emitted by the receiver, user can identify which zone is triggered.
6. BUZZER VOLUME
You can select the buzzer volume by switching the volume switch to “HI” or “LO” position.
The buzzer can be disabled by switching to the “OFF” position.
7. MUTE
When a sensor is triggered for a long period of time, you may stop the buzzer by pressing the mute button. When another signal comes again, you can disable the buzzer for all currently activated sensors by pressing
the mute button. The receive will beep again if it receives another signal.
For instance, if you are working on your lawn with the garage door open, you may want to disable the buzzer for this garage door only. Then you can press the “Mute” button after it starts to sound. If any other sensor is triggered, the receiver will sound again.
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
11. WARNING
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
-Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
-ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
12. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
13. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work, please :
1.visit our FAQ section at www.skylinkhome.com , or
2.email us at support@skylinkhome.com , or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N.
US Patent 6,597,291
©2005 SKYLINK GROUP
