Garage Door |
|
MonitorTM Sensor | Model |
1. INTRODUCTION |
|
The garage door monitorTM sensor is designed to monitor the status of
your garage door and advise you if the door is open. By placing the sensor on the door panel, you will be alerted when the door is open. When the garage door is open, receiver will beep and flash.
In this package, you should find a garage door monitorTM sensor, 3V lithium battery,
|
| 4 pcs 3 x 18 screws |
Clip |
| 1 pc 2 x 5 screw |
3V Lithium |
| |
| Garage Door | |
| battery | |
| MonitorTM Sensor | |
|
|
Mounting plate | |
|
Please follow the instructions below to set up your garage door monitor sensor properly.
2.SET UP THE GARAGE DOOR MONITORTM SENSOR
1.CODE CONNECTORS
In order for the sensor to communicate with the receiver properly, the sensor’s code must match with the receiver’s code. Code connectors 1 to 6 can be found by opening the top cover of the sensor and the back cover of the receiver. User is required to set these code connectors randomly and the code settings on the sensor and receiver must be the same. Each position of the code connector can be set to “+”,
Open the top cover
Clip
Note: A connector can be removed with the clip, as shown.
Code Connectors on Sensor
Note: If you experience interference from a nearby system, which could accidentally trigger your system, please change the code settings on the sensor and receiver. The code setting on the sensor and receiver should still match after changing the code setting.
‘0’ 
‘+’ 
‘-’
‘-’2. ZONE CONNECTORS
Each receiver can work with up to 4 different sensors (to represent 4 different zones on the receiver). There are 2 connectors that determine the zone number 1, 2, 3 and 4. These 2 connectors can be found by opening the top plastic cover, near the code connectors with marking “A” & “B”. Please follow table 1 to set the zone.
| 2. SET UP THE GARAGE DOOR MONITORTM | SENSOR (CONT) | ||||||
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| A | B |
|
|
|
|
|
|
|
|
|
|
|
|
| Zone | Zone 1 |
| + | + |
|
|
|
| Zone 2 |
| + | - |
| |
|
|
| connectors |
|
| |||
|
|
|
| Zone 3 |
| - | + |
|
|
|
|
| Zone 4 |
| - | - |
|
|
|
|
|
|
| Table 1 |
|
|
“+” in the table means the connec tor for that position should be placed on the posts.
3. POWER UP THE GARAGE DOOR MONITORTM SENSOR
After setting up all the connectors, the sensor is ready to be powered up.
Remove the top cover on the sensor and insert the 3V lithium battery to the sensor as shown in the diagram.
After insert the battery to the sensor, the receiver will respond to the transmitted signal depending on the orientation of the sensor.
“+” positive side up
Insert 3V lithium battery to the sensor
If the sensor is face up in the vertical position, the green LED on the receiver will glow steadily, indicating the sensor is in a closed position.
If the sensor is face down in the horizontal position, one of the red LED on the receiver will flash, and the buzzer on the receiver unit will also emit beeping to indicate a door is open.
You can change the orientation of the sensor and | Vertical |
| |||||
|
|
|
|
|
| ||
you should see the change in response of the |
|
|
|
|
|
| |
receiver. If the sensor and receiver are working |
|
|
|
|
|
| |
properly in close proximity, you can now begin to |
|
|
|
|
|
| |
install the sensor onto your garage door. |
|
|
|
|
|
| |
NOTE: It is normal to hear a rattle from the | Horizontal |
| |||||
|
|
|
|
|
| ||
sensor when tilted or rotated to another position. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| 4. INSTALLATION |
|
|
|
|
|
|
|
|
|
| ||||
|
|
| |||||
| Unplug the power cord of your garage door opener |
| |||||
WARNING | before installation to ensure power is not connected. |
| |||||
|
|
|
|
|
|
| |
Attached the sensor to the garage door with
For wooden garage doors, it is recommended to use the mounting plate and screws as well.
