Universal Garage Door |
|
Remote Control | Model GS1 |
1. INTRODUCTION |
|
|
|
Congratulations on your purchase of GS1, the package includes Skylink® garage door receiver
Garage Door
Receiver
Smart ButtonTM
| Double Sided Tape | |
Crimper | Garage Door |
|
| Transmitter |
|
| G6T3 | Visor Clip |
Double Sided Tape | (Battery inside) Mounting | |
Bracket |
|
Connect the receiver - Smart ButtonTM
2. RECEIVER INSTALLATION
| Unplug the power cord of your garage door opener before installation to ensure |
| power is not connected. |
| DO NOT let children use the gargae door Transmitter without adult supervision. |
WARNING | Children can injure themselves or others by the garage door. |
DO NOT use remote to control the door without safety beams. |
2. RECEIVER INSTALLATION (CONT)
If the Smart ButtonTM
contact Skylink® to purchase the adapter.
Rating of the transformer:
12V DC, 100mA Diameter of DC plug : 3.5mm
7. Secure the SmartButtonTM
Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.
Note: After installation of the “Easy Clip TM ”, if you want to
3. PROGRAM TRANSMITTER G6T3 TO RECEIVER GB-318
You need to do the programming in order to add the transmitter to a receiver.
1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.
Wall Button
Ribbon Wires
NOTE:
Ensure the ribbon wires are not twisted but laid flat inside the clip.
Easy ClipTM
Smart ButtonTM
To add remote controls, follow the instructions below:
1.Press the learn button on the side of the Smart ButtonTM
2.Once the learn button is pressed, the LED will flash quickly. Release the learn button.
3.Within 30 seconds, press any one of the 3 buttons on the transmitter that you want to program to the receiver.
4.Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes in standby mode.
5. You may now operate the garage door opener with this new remote control.
6. To program this transmitter to control another receiver, repeat process (1) to (4) to program another button on the remote control.
If your wall button ribbon wires are not the same kind as shown in the diagram, please refer below (4) or visit our website www.skylinkhome.com or contact us for more information.
3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.
Press / lock
Ribbon Wires
4. OPERATION
If the red LED flashes slowly, the Smart ButtonTM
Press the programmed button on the remote control or Smart ButtonTM
5. ERASE TRANSMITTERS
To erase unwanted remote control(s)from the memory of Smart ButtonTM
4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM
a) Disconnect the existing wall button from the wall.
b) Connect the 2 wires from the Smart ButtonTM
c) Reconnect the wall button back.
5. If the wall button wires are hidden inside the wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door
opener.
6.Power up the garage door opener, the red LED on the Smart ButtonTM
1.Press and hold the learn button for approximate 10 seconds.
2.The LED will flash rapidly after 10 seconds to indicate all the pro- grammed remote controls have been erased. You may now release the learn button.
3.You have erased all the remote controls programmed to the Smart ButtonTM
6.TROUBLE SHOOTING
Q:What can I do if the door opener does not react after I press the button on the transmitter ?
A:- Ensure when the button on the transmitter is pressed, the red LED on the transmitter comes on. Otherwise, check if the battery is inserted properly.
-Make sure the correct button on the transmitter is pressed.
-Ensure the wires that were previously connected to the wall mounted door control are not loose.
-Ensure the transmitter has been programmed to the receiver. Refer to section 2 for how to program a transmitter to the receiver.
7. TRANSMITTER MOUNTING METHOD
This