3 Installing the Switch

5.Select the Master unit in the stack by pressing the Master button in on only one of the switches. Only one switch in the stack can operate as the Master, all other units operate in slave mode. If more than one switch in the stack is selected as Master, or if no switches are selected, the system will select the unit with the lowest MAC address as the Master.

Stacking Topologies

All units in the stack must be connected via stacking cable. You can connect units in a simple cascade configuration, connecting Down ports to Up ports, from the top unit to the bottom unit. Using this “line” topology, if any link or unit in the stack fails, the stack is split and two separate segments are formed. The Stack Link LEDs on the units that are disconnected flash to indicate that the stack link between them is not functioning (see Table 1-2 "System Status LEDs" on page 1-4).

When using line topology and a stack link failure occurs, the stack reboots and a Master unit is selected within each of the two stack segments. The Master unit will be either the unit with the Master button depressed or the unit with the lowest MAC address if the Master button is not depressed on any unit. When the stack reboots and resumes operations, note that the IP address will be the same for both of the stack segments. To resolve the conflicting IP addresses, you should manually replace the failed link or unit as soon as possible. If you are using a wrap-around stack topology, a single point of failure in the stack will not cause the stack to fail. It would take two or more points of failure to break the stack apart.

If the Master unit fails or is powered off, the backup unit will take control of the stack without any loss of configuration settings. The Slave unit with the lowest MAC address is selected as the backup unit.

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the socket located at the back of the device.

Figure 3-8 Power Socket

2.Plug the other end of the cable into a grounded, 3-pin, AC power source.

Note: For international use, you may need to change the AC line cord. You must use a line cord set that has been approved for the socket type in your country.

3-8

Page 41 Page 43
Page 42
Image 42
SMC Networks SMC8926EM, SMC8950EM manual Connecting to a Power Source, Stacking Topologies
Page 41 Page 43

SMC8926EM, SMC8950EM specifications

SMC Networks has established itself as a prominent player in the networking and connectivity market, offering a range of professional solutions designed for small to medium-sized enterprises. Among its notable products are the SMC8950EM and the SMC8926EM, two advanced Ethernet switches that cater to the need for reliable and efficient networking.

The SMC8950EM is an enterprise-class managed switch that delivers high-performance capability with 48 10/100/1000Mbps Ethernet ports, providing extensive connectivity for various devices on a local area network. Its architecture is designed to handle high traffic loads, making it apt for environments where speed and reliability are paramount. This switch supports multiple protocols, including VLANs, which allow for flexible network segmentation and improved security. The SMC8950EM also features several Layer 2 and Layer 3 management protocols, enabling the switch to support advanced routing, Quality of Service (QoS), and network traffic management.

On the other hand, the SMC8926EM is a compact yet powerful switch equipped with 24 10/100/1000Mbps Ethernet ports, making it ideal for smaller installations or branch offices that require scalability without compromising on performance. With support for Power over Ethernet (PoE), the SMC8926EM simplifies the implementation of IP phones, security cameras, and wireless access points, making it particularly useful in environments where power outlets may be limited.

Both models employ advanced technologies, such as network storm control and link aggregation, to enhance performance and ensure seamless connectivity. They also provide comprehensive network monitoring capabilities, allowing administrators to manage traffic and troubleshoot issues proactively. The user-friendly web interface facilitates easier management and configuration, while SNMP support enables integration with existing network management systems for enhanced visibility and control.

Ultimately, the SMC8950EM and SMC8926EM represent robust networking solutions that address the challenges faced by modern enterprises. With their combination of high performance, advanced features, and scalability, these switches are well-suited for companies looking to build a reliable and efficient network infrastructure. Whether for a large organization or a small branch office, SMC Networks continues to deliver products that meet the evolving needs of users worldwide.
Top Page Image Contents