10 | INSTRUCTION ON MOUNTING AND USE | GB |
Consult the designs in the front pages referenced in the text by
alphabet letters. Closely follow the instructions set out in
this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined.
Description of the hood - Fig. 1
1Control panel
2 Grease filter
3 Grease filter release handle
4 Halogen lamp
5 Vapour screen
6 Vapour screen guides
7 Air exit
8 Fairing (supplied in two sizes)
9 Fixing points for cabinet
10 Inspection door for the suction group (ACCESS ALLOWED ONLY BY A QUALIFIED TECHNICIAN)
Installation - Fig. 5-6
The cooker hood must be placed at a minimum distance of 43 cm from the cooking plane for electric cookers and 65cm for gas or mixed cookers.
The hood is equipped with a top air outlet B for discharge of fumes to the outside (Ducting version – exhaust pipe and pipe fixing clamps not provided).
Where it is not possible to discharge cooking fumes and vapours externally, the cooker hood may be used in the filter version by mounting an active carbon filter and the deflector F on the connection ring placed on the exit perforation B (Fig. 3), the fumes and vapours are recycled via the deflector.
The models with no suction motor only operate in ducting mode, and must be connected to an external suction device (not supplied).
Preliminary information for installation of the hood: Disconnect the cooker hood from the electrical mains during the electrical connection phase.
The cooker hood is designed for installation inside a wall cabinet.
It is recommended to install the cooker hood only inside a cabinet of suitable dimensions.
Do not tile, grout or silicone this appliance to the wall. Surface mounting only.
Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed, in case maintenance is ever required.
Refer to figure 2 for useful information for safe installation and for eventual perforations to perform at the base of the cabinet for air evacuation, for the
connection cable and to permit to access the electronic card that controls the cooker hood operation (ACCESS ALLOWED ONLY BY QUALIFIED TECHNICIAN).
Warning!
The cooker hood is supplied with 4 side spacers (2 for the right side and 2 for the left side), these are useful when the width of the housing cabinet for the cooker hood motor body is wider than 6mm. In this instance the spacers should be mounted outside the cooker hood body corresponding to the perforations for the cabinet fixing screws (Fig.
1 . Measure the cabinet depth (consider also the cabinet door) as for a depth of up to 315mm will require the mounting of 37mm fairing, and for measurements over 315mm will require the mounting of 75mm fairing.
The fairing C should be fixed to the cooker hood body
brackets using 4 screws (fig. 3).
2 . Fix the air exit connector B above the cooker hood body (fig. 3).
Only for Filter Version:
place the deflector F on the exit connector.
Fix the filter holder frame inside the cooker hood, firstly above on the rings R set in the body, then on the base using the two screws S (fig. 3).
3 . Apply the supplied template first to the right and then to the left (fig. 4.1) or, if supplied, apply the apposite template to the wall (fig. 4.2 – only in case of models conceived for fixing to the wall) and making holes as indicated (for the templates for fixing to the wall units 3 dead holes are indicated, 2 of Ø 2mm and one of Ø 5mm, while for the template for fixing to the wall, 2 holes of Ø 8mm).
ATTENTION! TEMPLATE AND FIXING TO WALL UNIT
The lower and back edge of the template must correspond to the lower edge of the wall unit.
ATTENTION! TEMPLATE AND FIXING TO WALL The lower edge of the template must correspond to the lower edge of the hood.
Only for models with fixing hooks: make the holes and fix two hooks with screws and dowels
(J – fig. 4.2).
Install the two supplied Y brackets with two screws and washer each onto the upper side of the hood (fig.4.2).
4 . Insert the body of the hood inside the wall unit (fig. 5). This can remain temporarily in position:
a)in case of fixing to the wall unit, using lateral springs D to imbed into the Ø 5mm dead holes (to do this, press the lateral springs towards the inside of the body of the hood using a screwdriver as a liver.
b)in case of fixing to the wall, with the hooks and the brackets (the bracket have adjustable positioning screws).
ATTENTION!
Check that the electric cable and the smoke outlet are accessible to facilitate successive connections (and for technical assistance and maintenance interventions).
5.Check that guides G (fig. 6) are perfectly parallel to the lower edge of the wall unit, after which, ONLY in the case of fixing to the wall unit, definitely fix the body of the hood to the sides of the wall unit with 4 screws (E – fig. 6 – two per side). The screws are to be inserted from inside the body of the hood on the wall unit in correspondence with the 4 Ø 2mm blind holes previously made (see operation 3).
6 . Insert the cooker hood cabinet base on the bracket guides G then carry out the electrical connections of the cooker hood cabinet base to the casing (fig. 7).
7 . Regulate the cooker hood cabinet base in order that the frontal part is in line with the cabinet (H - fig. 8) then block the cooker hood cabinet base using 2 screws (one per side - L - fig. 8 – To insert these two screws you will need to remove the filter grill and screw them on the inserts that are fixed on the mantel guides).
8 . Fix the cooker hood cabinet base to the cabinet using the 2 screws M (fig. 8), use 2 of 4 perforations available and check that the screws are fixed to the cabinet.
9 . Remount the grease filter, connect the cooker hood to the electrical network and to the discharge tube, check the perfect operation of the cooker hood.
