Installation instructions, For Great Britain Only | Smeg STA6249

FOR GREAT BRITAIN ONLY:

Installation instructions

FOR GREAT BRITAIN ONLY:

THIS APPLIANCE MUST BE EARTHED.

Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

1.Remove the fuse cover A and fuse B.

2.Fit replacement 13A fuse into fuse cover.

3.Refit both into plug.

The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.

Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local electrical store.

8

Image 9

Smeg STA6249, STA6248 instruction manual Installation instructions, For Great Britain Only, Fuse replacement

Contents

GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Safety and operating instructions Safety instructionsUSES OTHER THAN THOSE DESCRIBED ABOVE NEVER BE REMOVED THIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELS Installation instructions 2. Installation and hook-up2.1 Water supply connection DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY 2.2 Electrical connection and precautions NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD FOR GREAT BRITAIN ONLY Fuse replacement 3. Description of the controls User instructionsSELECTED PROGRAM INDICATOR LIGHTS 3.1 Upper panel SETTING THE WASHING PROGRAM AND SWITCHING ON DELAYED START BUTTON on some models onlyDELAYED START LIGHTS on some models only Only run the soak program with half loads 3.2 Washing programs Before starting a washing program make sure thatThe correct amount of detergent has been added to the dispenser CHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT REMOVING THE DISHES END OF CYCLE 4.1 Using the water softening system 4. Operating instructions ADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensers ADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTING During the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENT 4.3 General warnings and recommendations 3/1 ProductsCorrect loading of the dishes helps ensure optimal washing results Dishes and objects in copper, tin, zinc or brass these tend to stain 4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKET ADJUSTING THE UPPER BASKET Version C with adjustment in three positions on both sides CLEANING THE WATER INTAKE FILTER 5. Cleaning and maintenanceCLEANING THE SPRAY ARMS 5.1 General warnings and recommendations GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE CLEANING THE FILTER UNITPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tap If the dishes are not being cleaned properly, check that TROUBLESHOOTING MINOR PROBLEMSBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap again If the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank FAULT 6. TroubleshootingSafety level E1 E2 E3 E4 E5 E6 Turbine flow-regulator malfunction E7 E8 E9Alternate washing system malfunction Water intake system malfunction Electrical characteristics TECHNICAL DATAWidth Height depending on models Capacity Water supply pressure