Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper NZM19481KWV important safety instructions

Models: NZM19481KWV

1 41

Download 41 pages 47.73 Kb

Page 39

Image 39

NOTES

Page 39

Image 39

Snapper NZM19481KWV important safety instructions

Contents

NZM19481KWV NZM21521KWV NZM25611KWV Safety Instructions & Operator’s Manual forMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES MODELSPROTECTION AGAINST TIPOVERS IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PROTECTION AGAINST TIPOVERSOPERATION IMPORTANT SAFETY INSTRUCTIONSPREPARATION SAFE HANDLING OF GASOLINEOPERATION IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE MAINTENANCETABLE OF CONTENTS Section 1 - FAMILIARIZATION 1.1 INTRODUCTION1.2 NOMENCLATURE WEAR HEARING PROTECTION WARNING ! AVOID SERIOUS INJURY OR DEATH Section 2 - SAFETY MESSAGES AND SYMBOLSDANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS MOTION CONTROL LEVER OPERATION PARKING BRAKE LEVER OPERATIONDANGER! ROTATING BLADES IGNITION SWITCH Section 2 - SAFETY MESSAGES AND SYMBOLSPUSH SWITCH “DOWN” TO KEYSWITCHSection 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LISTDO NOT allow operation of the machine by untrained personnel Section 3 - OPERATING INSTRUCTIONS 3.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE3.2.1. STARTING ENGINE LEVER SHOWN IN THE NEUTRAL LOCK POSITION KEYSWITCH SHOWN FROM OPERATOR’S VIEW POINTSection 3 - OPERATING INSTRUCTIONS PARKING BRAKE LEVER IN ENGAGED “ON” POSITION MOTION CONTROL LEVER3.3 CUTTING HEIGHT ADJUSTMENT Section 3 - OPERATING INSTRUCTIONS3.4 OPERATION- MOTION CONTROLS 3.4.1. DRIVING MACHINE 2. Engage parking brake Section 3 - OPERATING INSTRUCTIONS4.2.1. CHANGE ENGINE OIL Change engine oil as follows Section 4 - MAINTENANCE4.2 SERVICE - AFTER FIRST 5 HOURS 4.1 INTRODUCTION4.2.3. CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting Section 4 - MAINTENANCE3. Other Lubrication Points Section 4 - MAINTENANCE4.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings 2. Hydro Pumps4.6 DECK REMOVAL Section 4 - MAINTENANCE4.7 HYDRAULIC FLUID FILTERS Section 4 - MAINTENANCEDANGER Section 5 - ADJUSTMENTS & REPAIRSection 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS Continued From Previous Page5.2.1. MOWER DECK ADJUSTMENT LEVELNESS SIDE to SIDE and FRONT to REAR Section 5 - ADJUSTMENTS & REPAIR 8. Move deck lift lever and set the mower deck tothe highest cutting position and recheck side to side The traction drive belt tension does not require Section 5 - ADJUSTMENTS & REPAIR5.7.2. BELT REPLACEMENT Section 5 - ADJUSTMENTS & REPAIR5.6 TRACKING ADJUSTMENT 5.7 MOWER DRIVE BELT REPLACEMENT5.9.2. BLADE SHARPENING Section 5 - ADJUSTMENTS & REPAIR5.8 ENGINE ADJUSTMENTS & REPAIR 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS5.10 BATTERY 5.10.1.BATTERY REMOVAL Section 5 - ADJUSTMENTS & REPAIR5.10.5. NEW BATTERY PREPARATION 1. Remove battery from carton Section 5 - ADJUSTMENTS & REPAIRBattery Condition Chart 5.10.4.BATTERY TESTINGBEARING REPLACEMENT Section 5 - ADJUSTMENTS & REPAIR5.12 HYDRAULIC SYSTEM, PURGING Section 5 - ADJUSTMENTS & REPAIRPROBABLE CAUSE TROUBLESHOOTINGPROBLEM Trouble Shooting Continued on Next PageLoss Of Traction TROUBLESHOOTINGBattery Will Not Charge Machine Will Not Move48” DECK SERVICE SCHEDULEMAINTENANCE PARTS MAINTENANCE/REPLACEMENT PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Call the Snapper Customer Relations Center at SNAPPER PRODUCT REGISTRATION FORMEastern Standard Time Monday through Friday from 8am to 6pm Saturday from 9am to 1pmPage Page Page Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIESMANUAL No. 7-5627 Rev 1, 8/4/03